FGHS2334KW3 Frigidaire Refrigerator - Instructions

Disconnect the two water supply tubes at the base of the Water Filter Base. Using a 7/16" open end wrench, press up on the blue "O" rings to disconnect the tubes. Use a Using an 8" long magnetic phillips head screw driver I was able to unscrew the 4 short screws holding the original water filter base and the immovable attached water filter. Replacement was easy. Simply slide the new base into the fixed slot on the refrigerator and reinstall the 4 holding screws. Reconnect the water supply tubes to the Water Filter Base. Install a new water filter.

Old valve comes out with 2 screws, water lines removed and reinstalled on new valve just as they came off the old valve. Entire job took less than 10 minutes. Very easy replacement.

It was very easy to insert the new shelf door into the refrigerator slots.

Put on new shelf in seconds. What a wonderful way to be able to purchase the perfect part easily through the internet. I ordered the part on Sunday and received it on Tuesday. THANK YOU Parts Select!!! K.F.

There was no repair needed. I broke the glass shelf that inserts to a plastic frame that holds the fruit/veggie drawer on the fridge.

I found the part very easily on the site and ordered it. The part came exactly as described on the Web site.

New part fit nicely in an instant. Only issue is that it is a white replacement part and ours was clear...not a big deal because this is the bottom drawer so you really don't even notice.

I received the part and slid it down the molded runner and secured it.

Removed and replace solenoid manifold valve in rear of appliance using inadequate You Tube video. Removed and replaced augur motor after dismantling various housings using a seriously mistaken You Tube video. The latter video informed us that the yoke that screwed on the motor's shaft was a reversed Left Hand thread. It wasn't at all, and we struggled to figure that out. The people that make these videos leave out steps that they thunk are obvious, but aren't at all.

Called "local" repair warehouse and ordered part. They shipped the wrong part. Went on-line to Part Select and got the right part.

I was able to replace the housing by only removing the front cover, the e-ring and washer and the 3 hex-head screws. I was able to work the old housing around to get the actuator arm off and then get it properly inserted into the new housing. Attach the new housing, IMPORTANT: make sure you get the fixed-blades and spacer assembly in the slot of the housing that holds them in place, replace the e-ring and washer, check that the actuator arm operates the door properly and replace the front cover. The videos can be helpful but these shortcuts will save some time.

1. Using Philips head screwdriver, remove plastic hinge cover on top of refrigerator door.
2. Remove bolts using socket wrench.
3. Lift door from bottom hinge.
4. With Philips head screwdriver remove screw holding bearing in place on bottom of door.
5. Remove old bearing.
6. Install new bearing.
7. Replace fridge door using reverse steps.
8. Enjoy your handi-work.

Can't supply any info that would be helpful. Ordered a " badge" that covered 100% of the scratch and stuck it on. Scratch now covered and problem solved. Thanks for asking.

I followed the instructions, my ONLY issue was about the Part 46 the Ice Dispenser Actuator Rod. The front of the arm has flared out grooves and it didn't warn me about making sure the rod is properly aligned thru part 23 Front Plate or else when the ice maker actuates the rod it will not move properly if the grooves are not aligned on each side of the Front panel. I hope you can understand what I mean, if not just look at how the Part 46 rests in Part 23

DID IT JUST LIKE THE VIDEO SHOWED. UNHOOKED ELECTRICS, CUT TUBING, HOOKED UP ELECTRICS THEN TUBES TO NEW PART. PIECE OF CAKE.

Open freezer
Pry the switch out (bottom first, then push the tab on top while prying out)
Move wires to
New switch
Push switch in
Test