FGHB2869LE1 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from SEMINOLE, OK
- Parts Used:
- 5303918214
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
refrig.freezing up.
I followed the instruction video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shirly from FRAZIER PARK, CA
- Parts Used:
- 5303918214
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
cold freezer warm refridgetor
removed lower panel in freezer, sniped off old defrost thermostat.
Spliced in new part. reconnected power and it's up and running.
Spliced in new part. reconnected power and it's up and running.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Warrensburg, MO
- Parts Used:
- ULTRAWF
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
time to change water filter
first, there many different water filters. your experience will be different according to your water filter type.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from NEW BERN, NC
- Parts Used:
- 241830001
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
ice maker failure, broken auger housing
Remove ice maker, completely disassemble, being careful with the styrofoam around housing. This is a very weak part and takes much load from auger. Use a white, high strength tape to bind around the housing with, (very important) or you'll be doing this again as it is a failure point.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wes from FARMINGTON, NM
- Parts Used:
- 5303918214
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Refridgerator too cold...freezing food,could not turn down
First,read "how to" on the internet because the thermostat comes with no instructions and unplug refer. Second, remove food and lower rear panel. Third, pull off thermostat from tube it clips to, unhook wire harness,and cut wires.Fourth,add heat shrink tubing from store(that supplied is way too big) and connect wires with automotive connectors;shrink-seal tubing with flame.Fifth, re-install everything, and replace food.Sixth,use a thermometer to check temp and adjust controls as needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Pawleys island, SC
- Parts Used:
- 242253002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Refrigerator water dusoeswr stopped working
I removed the defective water valve. All wiring and tubing connectios were color coded.
It connected the water tubes and electric plugs to new water valve.
The water dispenser worked perfectly after I reconnected everything.
It connected the water tubes and electric plugs to new water valve.
The water dispenser worked perfectly after I reconnected everything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daune from OCALA, FL
- Parts Used:
- 241675704
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Ice Maker was making ice erratically
After sending PartSelect the info to their troubleshooting dept. about my ice maker, they recommended replacing the ice solenoid. I did so at a cost of $102. No change, turned out replacing the ice maker(did not purchase from PartsSelect) was the issue and works fine now.
So wasted $102. FYI the part took 6 days to arrive.
So wasted $102. FYI the part took 6 days to arrive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheryl from Riverdale, NY
- Parts Used:
- 242037202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Our older bin shelf was cracked
Simply removed old shelf and installed new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from BRAINTREE, VT
- Parts Used:
- 218755402
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
A set scew was ordered twice.
The first order arrived in a huge box and there was no scew to be found, the box had wholes in it. I was given a refund and told to order again.
The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.
The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ORLANDO, FL
- Parts Used:
- 241829001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
ICE WOULDN'T DISPENSE FROM ICE BOX
I read other suggestions trying isolate auger motor shaft with pliers while turning bar drive. needle nose pliers could hold the shaft. bar drive just would spin. so took the whole ice box assembly out
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Lexington, SC
- Parts Used:
- 5304537408
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
THE GASKET LOCKING INSERT DID NOT FIT THE BOTTOM OF THE DOOR.
I REMOVED THE OLD GASKET BEING VERY CAREFUL TO SEE EXACTLY HOW IT CAME OFF. I INSERTED THE LOCKING INSERT INTO THE TRACK IN THE DOOR WHICH DID NOT FIT AS THE OLD ONE DID. AFTER USING TREMENDOUS FORCE WITH MULTIPLE TOOLS I DID MANAGE TO GET THE TOP AND THE SIDES TO LOCK INTO PLACE AND EVENTUALLY HOLD. THE BOTTOM OF THE GASKET DID NOT HOLD SO I USED CLEAR CAULK AND TAPE TO HOLD THE GASKET IN UNTIL THE CAULK CURED. AFTER THE CAULK CURED THE GASKET HAS, SO FAR, REMAINED TIGHT.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from NEW WINDSOR, NY
- Parts Used:
- 241779401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
1 Broken plastic mullion hinge. Mullion was not operating correctly.
Removed screw on Mullion so that the replacement hinge can slide onto the small plastic bracket on the door. Slid the mullion on the hinges and screwed in muliion (1 screw).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine from Arlington, VA
- Parts Used:
- 242161202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
very Simple!
Insert the bottom part of the trim first, then pull up to snap on the top. PartSelect.com is a fantastic website!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWIN from ELWOOD, IN
- Parts Used:
- 5308000010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
loud noise fan blade broke,off balance
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from LEHIGH ACRES, FL
- Parts Used:
- 218755504
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
No problems
I had no problems. Screws arrived sooner than expected. It was a very simple installation. Very pleased with both the product and service.
Was this instruction helpful to you?
Thank you for voting!