FGHS2634KE0 Frigidaire Refrigerator - Instructions

I ordered the part from PartSelect using the part number located on the valve itself. The part was delivered in less than 48 hours from the time I entered it. Replacing the valve was easy and went according to the online video instructions provided by PartSelect. The only thing extra was that I had to replace the brass compression fitting on the copper tubing connected to the inlet of the valve. The old one would not seal properly. The compression fitting was about $1.50 at Home Depot. This is my third purchase from PartSelect and I continue to be impressed by them.

I used pliers to get the remaining shelf support studs out, then the new ones just snapped right in place. Very easy repair!

Simply detached the old ice container by removing four screws and removing one screw holding the lever onto the bottom of the container. A bit of advice; make sure you note how the spring is attached to the lever before removing the screw. It took me a bit to determine how the spring activated the lever when I was reattaching it to the bottom of the container. Also, double check your order before you finalize it. I must have inadvertently hit the item twice so I received two of them. This resulted in me having to return one item and paying for extra shipping both ways. I received the part within two days of my order. It was a very fast turn-around. Also, when I realized that I received two parts and had to call to explain the situation, I found the person on the phone to be extremely helpful and courteous. She sent me information regarding how to return the product and didn't ridicule me once for my stupidity.

Removed the previous water filter. Installed the new water filter.
I then filled a large glass full of water from the water dispenser several times to clear the air from the filter and lines.

Time to install, less than 8 minutes.

Thank you Parts Select!

The bin was easy to install on the door, just lined the bin notches with the door notches , and push down lightly the non is locked in, done

Turn off power. Remove ice tray. Back out the two screws with nut driver and just lift ice maker off screws. Do not bend the water fill tube in the back . Now unplug the wire and remove ice maker .
To replace, match the color of wires on plug. Adjust wires in place and water fill tube and back on to the screws. Hold in place and snug screws. Turn power back on. In 4 to 5 hours your ice will start .
FED-EX UT to MN was 13 days to deliver .

Looked it up on how to, follow the video
. Very easy 1-2-3 it was out and new one in..........??.

Downloaded a schematic of the ice container. Disassembled the ice container, keeping track of which different type of screws went where. Followed the schematic to ensure proper sequence of blades and spacers. Manually rotated unit prior to installing into the freezer in case of binding. Finished.

It was real easy took the lines off one by one put them on the new unit one by one same with the three plugs than tighten new unit back on fridge.

But I have back ground mechanical skills, I did see the video one time, and everything went smooth......

take the broken one out and replace it with the new one. the service was very good, from ordering the part, when it arrived only one day after I ordered it, it was broken in the delivery, I called them and they had another one on the way by the end of the day. Will continually use parts select for my services

Biggest part of this repair is getting the correct part. You just slip it on. Your website was very good in the diagram that identified the part. Delivery was quck.
Thanks

Simply popped the bin into place and my refrigerator was a good as new again. Note, you have to push kind of hard to get the shelf into the correct groove.

You order your door bin by phone to PartSelect and wait. Wait for about 3 1/2 weeks to get a cracked and unusable piece of plastic. Then reorder and wait. Wait for about 2 weeks to get another cracked door bin. Now you decide to use this part or send this one back also. Don't worry, you get charged for shipping only once. I decided to use the second bin. It was not cracked from top to bottom like the first one. I'll see how long it last.

Had to disassemble the entire ice maker bucket. Simple and straightforward, didn't need any pictures or reference materials. Just time consuming.