FFHT1816LK1 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Earl from Peoria, IL
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drawer support rail was broken
Took one screw out to remove the old rail off by removing one screw placed the new one into the slot and replaced the screw and put the drawer back into the refrigerator
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bettie from Toledo, OH
- Parts Used:
- 240358008
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Had no freezer shelf.
I had to cut a little of of the ends of the shelf to make it fit. I used an angle grinder to get the job done and the shelf fits perfectly. By the way I paid for 3-5 day shipping and got it the very next day can't ask for better service than that.
Was this instruction helpful to you?
Thank you for voting!
refer door hinges were lost during the move in to our first home.
The center door hinge was still attached to the refridgerator so I only had to install the bottom and top hinges. I also moved the door handles to the other side so the doors open the "right" way. The hinges were just 2 bolts and 3 screws. Now, just if the repair man from our home warrentee company would show up to fix the refridgerator. It's blowing hot air!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathan from WELLS, ME
- Parts Used:
- 5303918202
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Refrigerator and freezer running to warm.
I watched the video on how to change the defrost thermostat. I removed the back cover inside the freezer then I pulled off the old defrost thermostat and then using a pair of wire cutters I cut it off and then bared a little of both of the wires and then slid the heat sherink and wire connectors on the existing wires and then slid the other ends of the wires into the wire connectors then crimped the ends of the connectors and then tried using heat on the heat shrinks but still used rubber electric tape over it. I clipped the new thermostat were the old one was and then reattached the freezer wall cover and plugged the refrigerator back in. 24 hours later I checked the temperature in the refrigerator and freezer and both are running a lot colder.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from FREEPORT, NY
- Parts Used:
- 240530601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Right drawer rail broke/ don't need left
Screwdriver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from Jersey City, NJ
- Parts Used:
- 5304507147
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
The refrigerator door did not come for the opening swing to be reversed
I ordered four bearing hinges and drill holes for the hinges on top and bottom of frezer and fridge doors insert the bearing hinges on the holes and all the other part on the door were able to reversed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacy from Chisholm, MN
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lunchmeat drawer support rail broke
husband did it in less than 3 minutes. took top shelf out with part attached. one little screw to remove broke piece and one screw to install replacement part, good as new. took longer to clean the shelf before replacing it back in fridge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from DUMAS, TX
- Parts Used:
- 240337103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
None
Real easy took out the broken ones and replaced with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from BAY CITY, MI
- Parts Used:
- 5304506471
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door handle broke off
used Phillips screw driver to remove two screws form the top off old handle on top of lower door. slipped new handle on the stud and installed screws in the top of handle .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from SOUTHFIELD, MI
- Parts Used:
- 240350608
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken glass on top of crispers
Since the glass was broken and gone I just had to slide the new glass on top of the crispers. This was not really a repair, just an exchange of new for the old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from FORT MYERS, FL
- Parts Used:
- 5304506471
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The handle on the refrigerator broke at the top
Removed the old handle by taking the screw out at the top and sliding the bottom part off. Then slid the new handle on at the bottom replaced the screw at the top and done. Took less than 2minutes from opening the package to done.
Was this instruction helpful to you?
Thank you for voting!
The door shelf retainer bars cracked.
The repair was quick and easy. I simply removed the old/cracked door shelf retainer bars and snapped the new ones into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from DAYTON, OH
- Parts Used:
- 240337103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Front upper edge of crisperpan was broken
Slid out old, broken pan and slid in new replacement pan.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dianna from HALE, MO
- Parts Used:
- 240364787
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My Crisper cover was cracked and broken.
I ordered the replacement part. Cleaned out the bottom of my refrigerator, popped in the new part, replaced the food and was siting in my recliner in under 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JUSTIN from NEW BRAUNFELS, TX
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Top cools bottom is weak
Unplug, remove 2 screws off back panel inside the freezer. Cut wires on old one and crimped in new one. Light to melt the shrink wrap that came with it. Pretty easy.
Was this instruction helpful to you?
Thank you for voting!