FFHT1725LS6 Frigidaire Refrigerator - Instructions

Unplugged refrigerator. Emptied freezer and removed ice maker and cover, need to unplug fan. Defrosted coils with hot water. Cut wires to thermostat as close to it ad possible to leave extra wire in case of an error. Stripped wire in new thermostat and put in shrink plastic then the wire crimp connector joining both light blue wires making sure wires were in before crimping them. Repeated with other dark blue wire. After used the heat gun to shrink the protective white tubing. The only thing i found not satisfying was tge tubing. It was too wide and too small. When i shrunk it did not cover the whole connector and was loose. I had to use a glue gun to cover both ends of each wire connector. Hope this helps other users.

A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.

Ordered and replaced

I just put the new one in with no problem

Just snapped the item into place.

A single screw holds the part in place. The ONLY challenge is seating the new slide so that the screw hole in the glide matches the hole in the support assembly. Initially setting the glide into place mismatched by about 1/16 of an inch toward the back of the refrigerator. Firmly grasping the new part after mating it to the two receivers on the support assembly, pull it toward you until it clicks into place. The screw should mate cleanly to the new part without any difficulty. Make sure you get the right or left side part, as they are not interchangeable.

It simply snapped into place. No tools required. A very simple repair.

The evaporator coil is behind the freezer. Remove the rack that makes the shelf and remove two 1/4” hex head screws I the back of the freezer to access the coil.
I used a hair dryer to melt the ice off the coil.
The thermostat clips on the refrigeration pipe to the coil. Remove the old thermostat and cut the wires at least a few inches from the thermostat. Clip the new thermostat on the pipe and strip about a 1/4” of the wire ends. The electrical connectors (provided with the new part) must be crimped to connect the wires.

This was the easiest thing to repair in my house! All I needed to do was to snap the appropriate new shelf in the place where the prior piece was and we were back in business. A caveat to anyone else who might try it-get your Mfgr/model number straight as well as measure the length of the shelf to be replaced. Since my brand was not listed in the pull-down menu for replacements, the first time I ordered the shelf replacement piece, I ordered the shelf that looked exactly like the one I was replacing however the replacement was a few inches too small! Thank you PartsSelect for an easy return policy and your guidance when I called

new drawer was received within 2 days and was extremely simple to install.

Simply removed screw from old rail, inserted it into new rail and connected the rail to the old shelf. A very easy fix and a money saver. Local techs wanted $75 just to come out and look at the problem. Local parts places didn't stock the part and gave an estimated delivery time of 3-5 weeks with a price $12 higher than you guys. I received the part from your company well within the promised maximum 5 day delivery time - 3 days! Thanks, you have a repeat customer.

Super easy it took no more than 5 minutes to replace the fridge door racks. Starting from opening the box when it arrived to closing the fridge door with the new racks in place. no tools needed, except a knife to open the box.

Easy peasy... took the shelf out of the fridge. Unscrewed the old rail. Screwed in the new one. Put the shelf back in. DONE!!!!

My local appliance repair shop said they would have to order the whole shelf in order to fix my problem. It was going to cost $50 and I'd have to wait 3 weeks.

Instead, I found you guys on the internet. The part cost $5 and I got in delivered in 2 days.... CAN'T BEAT THAT!!!!

Thanks

I had to loosen the screw holding the mounting block and increase the hole size to fit the screw on refrigerator

This was so easy it took longer to open the door than it did to install the rack. WOW. Nice to see something fits without messing with it. Thanks.