FFHI2117LB0 Frigidaire Refrigerator - Instructions

I started look inside ,disconnected power, and open all possible compartments to see any burned part. Fortunately I fined a small part look like melted and then i went online and make my research .Then i ordered that part and change it.

The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.

If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.

In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.

Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.

Hope this helps someone. :)

Took out top shelf, remove old screw and rail . Replace with new

I followed your video instructions, is very important to have this information.

Took out old replaced with new. Now it makes ice

I initially replaced the defrost timer, and later replaced it and the defrost thermostat. The defrost thermostat was the faulty component

My upper and bottom air diffuser was missing.
Purchased both air diffuser and placed it.

Removed 2 screws and broken part of handle. Set handle into screw holder on door, and fastened the top of handle with the 2 removed screws.

Took out old screws, removed broken handle. Put new handle in place, used old screws. Super easy!

inside the freezer compartment, remove four hex head screws from rear panel,lift panel forward and unplug wire assembly from panel. find old defrost thermostat attached to copper tube by clip on back of thermostat, unclip, snip two wires to thermostat, take new thermostat, strip 1/4"of wire from wires in freezer (thermostat is prestripped),insert light blue wire from thermostat and light blue wire from freezer into opposite ends of crimp connector and crimp securely. repeat with dark blue wires. set panel back in freezer,connect plug to back of panel, refasten screws and you are go to go! save yourself the price of a new refrigerator or $300 repair by repairman!

just pull the old off and put the new one on the magnetic strip inside the rubber was the key it just grabbed the area real easy.

1. Remove from box. 2. Snap into place. (30 sec.) + part arrive 2 days ahead of ETA (Ground Ship)

Ordered the Capacitor and the Thermostat Control. Parts were received in a matter of a few days, easy to install, but did not fix the problem. Had to call a repairman to fix the problem (compressor relay - this part not available to order for this model number with Parts Select). Will continue to use Parts Select in the future for other parts, but not happy that the actual part I needed was not available - had to use other methods.

Very Easy repair just needed a Phillips Head screwdriver. Unscrew two screws and slid the new handle in place and screwed it in.

When you purchase the part, it comes with two handles. One assumes that one is for the main part and the other is for the freezer. Actually, they are both the exact same size. Although the handle is not an exact match to the original it's close enough for a spare, garage fridge.

After reading some reviews there were complaints about having to buy two handles and other complaints about the handle breaking more than once so I'm just holding onto the second handle as a spare.

When life gives you lemons, make lemonade! Heck, I'm grateful to have my garage Frigidaire! Our <5 year old kitchen GE broke in May and we have been unable to get a suitable replacement. I am writing this on October 27, 2020.

Turned off water to inlet valve. Unbolted valve from back of unit, disconnect water supply line from valve, disconnected water line to ice maker. Put on new compression ring around water supply line. Pressed ice maker line into new valve, installed valve back on unit, then connected main supply line to valve. Works like a charm.