CRSH237LS3 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from PHOENIX, AZ
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Replace ice maker which was splashing water
Turn off ice maker
Slide wire harness shield off connector
Disconnected harness
Loosened 2 wall screws
Remove old ice maker
Installed new one reversing process
Slide wire harness shield off connector
Disconnected harness
Loosened 2 wall screws
Remove old ice maker
Installed new one reversing process
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob G from ANTHONY, KS
- Parts Used:
- WF3CB
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Ice maker not working good
Shut off water supply at the main, drained water from lines, pushed filter in from end of filter then pulled out. Removed the 2 plastic protecting tubes from the inlet and outlet stems. Made sure filter was facing same way as the old one, pushed filter in making sure it was locked, turned water supply on slowly, ran about a gallon of water thru filter. If not done the taste is odd. 5 minute repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Will from Katy, TX
- Parts Used:
- 241860803
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Ice not dispensing
Ice was not dispensing. Examined the ice bin and auger, noted that the plastic ring that holds the auger at the front of the bin was broken all the way around. Pulled out old bin, making sure the ice fill level was raised all the way up, and pushed in the new bin. The new bin filled with ice, which promptly turned into a solid mass of ice because the ice maker was also faulty. I replaced that as well and have not had any issues.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- winifred from LOUISVILLE, KY
- Parts Used:
- 297286803
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Coming from the refrigerator, there was an intermittent "clicking noise", occurring about every 30 seconds. The frig. eventually failed .
I removed the back cover and removed the clip holding the compressor- run capacitor and start relay. I replaced these 2 components and clean the dust from the frig., and from the bottom of the floor. I replaced the back cover ; Loss about $300 worth of meat when when the frig. failed. Then I thought that, during these turbulent times, there are many which don't have a refrigerator or any meat to place in it, The refrigerator is "running" normal again.
Was this instruction helpful to you?
Thank you for voting!
There was no problem with the installation just finding out what was wrong with it not making ice
Replaced bad parts with new parts it went easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from SYLVANIA, OH
- Parts Used:
- 240597203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
2 drawer undercounter beverage ref not getting cold enough. Wont get below 48°
Took drawers out by removing 2 screws on top of rail near front, then popped black plastic cover off in lower right inside cabinet...sensor just un plugged and new one plugged in easily...did not fix problem though...display set at 34 but bottom drawer reads about 40 at best and upper drawer reads around 55...dont think the 3 little fans inside on back wall have been running
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from EDGEFIELD, SC
- Parts Used:
- WF3CB
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
change water filter
great push old in came out and push new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dante from SOUTHOLD, NY
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice Maker ffss2614qpo
Looked it up on how to, follow the video
. Very easy 1-2-3 it was out and new one in..........??.
. Very easy 1-2-3 it was out and new one in..........??.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANGELA from MEBANE, NC
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator Light bulb went out
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
My previous ice maker made a ton of noise and stopped making ice
It was as simple as removing two hex head screws to remove the old ice maker, then aligning the new ice maker (ensuring the downspout from the water supply was directed into the opening designated for it) and then screwing the two screws back into place. The most difficult part is the space that you have to work with. It was a little difficult and frustrating, but put in place, an hour later we had ice and it's worked great since!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Lakewood, OH
- Parts Used:
- WF3CB
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Routine 6 month maintenance
Removed the old filter and took off the water caps and pushed it in place. Then I used a pitcher to clear the air from the line and we are good to go for 6 more months
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Orange City, FL
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
freezer filled up with ice leaking from ice maker shut off valve bad
It was real easy took the lines off one by one put them on the new unit one by one same with the three plugs than tighten new unit back on fridge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marisa from pearland, TX
- Parts Used:
- 240350613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken glass
I was really impressed with how easy it was to navigate through your website and found the exact part I needed. I immediately received my glass shelf it took all of 2 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Lockport, NY
- Parts Used:
- 241639502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One blade broke from condenser fan
The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.
I removed the broken fan from the condenser. This was very sipmle.
When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.
I removed the broken fan from the condenser. This was very sipmle.
When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.
Was this instruction helpful to you?
Thank you for voting!
Rust on Front Plate and Drive Blade
Downloaded a schematic of the ice container. Disassembled the ice container, keeping track of which different type of screws went where. Followed the schematic to ensure proper sequence of blades and spacers. Manually rotated unit prior to installing into the freezer in case of binding. Finished.
Was this instruction helpful to you?
Thank you for voting!