CFHT1843LS3 Frigidaire Refrigerator - Instructions

Simply slide the new glass insert in!

Unplug, remove 2 screws off back panel inside the freezer. Cut wires on old one and crimped in new one. Light to melt the shrink wrap that came with it. Pretty easy.

Literally all I needed to do for the door shelf was press it into place, and for the crisper drawer cover so just needed to remove the crisper drawers, lift away the glass shelf (after removing contents from the fridge, obviously) and then remove the drawer frame and replace the broken one (which again, had been broken from before I moved in here almost six years ago!), and then reassemble. It's very nice to have space for seltzer or beer cans in the door and not to have the sagging shelf like I had before. Worth the money and very easy to source.

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

Popped the old one out and pressed the new one in. Very easy. Pressed new one in my hands. Fits in a channel. Very easy

replaced broken one

Remove screws from lower hinge and carefully remove the door. In my case it was the lower bearing, flip door upside down being careful to remove anything which might fall off first. I removed the door stop and then pulled the broken bearing out with pliers. Then I pushed the new one in and reassembled it.

Slid the old shelf out. Attached meat drawer to new shelf and slid it in.

Just pushed the grill on

I take 2 crew on front of the fridge take the cover and fan out replaced the part and put everything back it’s a easy job thanks guys for the parts from Orlando fl

The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.

If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.

In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.

Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.

Hope this helps someone. :)

Turned off fridge circuit breaker
Removed all food from freezer and put in cooler.
Removed shelves from freezer
Removed ice maker
Removed 2 hex head screws
Tilted back evaporator cover and tried to unplug connection.
Found connection was iced over with a huge block of ice coming from water inlet to ice maker
Spent several hours trying to melt and chip away ice without damaging fridge.
Finally was able to break up ice with long flat head screwdriver and hammer.
Unplugged connector and was able to remove evaporator cover.
Cut wires near thermostat and removed
Stripped wire as needed and crimped new thermostat in place.
Used heat gun and lighter to melt heat shrink. This took a long time and required a lot more heat than expected.
Reconnected evaporator cover connection and reattached cover.
Reinstalled ice maker
Reinstalled shelves.
Put food back in
Turned circuit breaker back on.

Since the glass was broken and gone I just had to slide the new glass on top of the crispers. This was not really a repair, just an exchange of new for the old.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

After watching numerous YouTube videos I realized that my problem was either the timer or the thermostat. I purchased both for above $70 total and decided it was worth the gamble to self- repair it instead of buying a new refrigerator for $700 plus taxes and delivery charges. The videos were right on with excellent directions for replacing these 2 products. Only has one problem… the shrink wrap that came with the thermostat is very thick and will NOT shrink with a hairdryer. I hade to run to ACE Hardware to buy a heat gun and more shrink wrap