MRS22WNGW1 Frigidaire Refrigerator - Instructions

Removed power , unplugged wires and 2 screws then reversed the process 1 hour later first batch of cubes dropped into bin

I found PartsSelect on the web, input my appliance model# and type and a very easy to read diagram of my appliance appeared. I simply selected the parts I needed from the diagram,and the part numbers were displayed. I placed my order and 2 days later the parts arrived, and I installed them immediately. No fuss, no problem. Great Service!

A pretty easy, remove and replace, project. The spring that closes the fridge door had broken. Just pulled out the old part on top of the appliance and put in the new part. I noticed that part of the problem was that the bottem hinge needed a little lubrication too, as the door wasn't closing as easy as it should with the new part installed. I can't complain though, the side by side fridgeadaire is getting old and this was a very easy fix.

removed old fan and replaced it.3 screws and plug.Always unplug appliance when working on it.

I was able to replace the housing by only removing the front cover, the e-ring and washer and the 3 hex-head screws. I was able to work the old housing around to get the actuator arm off and then get it properly inserted into the new housing. Attach the new housing, IMPORTANT: make sure you get the fixed-blades and spacer assembly in the slot of the housing that holds them in place, replace the e-ring and washer, check that the actuator arm operates the door properly and replace the front cover. The videos can be helpful but these shortcuts will save some time.

First I determined the icemaker was the problem when it was no longer calling for water. You can hear that "whistle" for 6-7 seconds when it calls for water. Anyway, replacement was a piece of cake, but did not entirely fix my problem. I also had to flush the lines to the soloniods that allow water to flow through the filter and into the water storage tank because it was cloggged with a little piece of plastic.

We moved the refrigerator out so the drawer could be removed. (It was close to the wall) After removing the drawer the front of it had to be removed, then put on to the new drawer. The hardest part was that replacement because we had trouble getting it lifted up. Then the drawer was put in, refilled, and refrigerator moved back into place.

BOUGHT NEW ICEMAKER TOOK TWO SCREWS OUT, UNPLUGGED THE ELECTRICAL CONNECTION. REMOVED OLD ICEMAKER, PUT TWO SCREWS BACK INTO REFRIGERATOR(DON'T SCREW ALL THE WAY IN AS THE NEW ICE MAKER WILL FIT ON. HOOK ELECTRICAL CONNECTION AND ADAPTER (THAT COMES WITH IT). PUT THE DRAIN TUBE IN ITS SPOT, HOOK ICE MAKER ONTO THE TWO SCREWS TIGHTEN EM DOWN. I DID THIS RIGHT BEFORE I WENT TO A BIRTHDAY DINNER WITH MY HUSBAND, WAS ALREADY DRESSED AND READY TO GO AND I TOLD HIM ILL PUT IT IN SO WE CAN HAVE ICE WHEN WE RETURN. ENDED UP BEING A SURPRISE PARTY FOR ME AND WHEN WE RETURNED WE HAD ICE. IT WAS SO EASY EVEN A GIRL CAN DO IT!!

Unscrewed (loosen) screws lifted unit out unplugged electrical connection. plugged in unit hung on screws tightened screws and had ice in less then 1 hour. Rick

Loosen two screws, unplug power, lift it off, put new one on and make sure water chute is correct place, tighten screws!

This was the last step of serial repairs to the ice crusher portion of the ice maker. I have practically replaced the entire assembly. All the blades were installed incorrectly (at factory? Afterwards?) and had bent. That caused problems for other parts. I hadn't noticed that the housing was weakened and my prior repair I did something dumb and the door on housing wasn't closing properly, so it snapped. I bought a new housing and installed it. My #1 tip is WATCH THE VIDEO! There are some things that have to be put together just so. You need things to line up and be under slight tension from springs. Last time I had it under too much tension. The door got in the way of the blades and broke. So this time I was more careful to do it correctly. Everything is working perfectly now. This design is clever, and I feel like I can diagnose and fix it again in future. "Steve's" instructional videos are a huge help. He shows exactly what to do.

After determining the ice maker was getting water but not harvesting the ice, I ordered a replacement Ice Maker. Installation was easy. One electrical connection and two screws. Following the video to make sure I did not miss any steps I had ice in just a few hours. Just in time for a July heat wave!

Had to replace with a whole new part, had to take it all apart to replace

attached the bar to the end piece and slipped it into the proper opening. Easy I ordered the piece one morning and received it the next morning. Great service.

Simply popped the new end caps into place with the old guard and now it is tight and secure. Easy Peasy. Of course all this is after the operator at PartSelect ordered the right part for me; I had ordered the freezer door end cap, not what I wanted. I received the correct part the very next morning. Returning the wrong part was a breeze too.