MRS22WRAD0 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Judy from ROYSE CITY, TX
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Freezer wasn't cooling - compressor not engaging
Ordered the Capacitor and the Thermostat Control. Parts were received in a matter of a few days, easy to install, but did not fix the problem. Had to call a repairman to fix the problem (compressor relay - this part not available to order for this model number with Parts Select). Will continue to use Parts Select in the future for other parts, but not happy that the actual part I needed was not available - had to use other methods.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Grayson, GA
- Parts Used:
- 5303918277
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker wasn't making ice
Occasionally, we'd get one batch of ice cubes and a frozen lake of water in the bottom of the ice tray.
The installation was easy and I won't bother duplicating the comments of others who have installed this part.
One word of caution: The ice maker contains a heating element on the bottom. That element is apparently live even when the ice bar is in the upper (off) position. When I unscrewed the old ice maker and went to lift it off the bolts, I severely burned my finger on the bottom of the old ice maker because apparently I started the repair in the middle of the heating cycle.
I highly recommend that you unplug the ice maker entirely before doing the replacement and gingerly ensure that the unit isn't hot before touching it. You'll save yourself a nasty burn.
The installation was easy and I won't bother duplicating the comments of others who have installed this part.
One word of caution: The ice maker contains a heating element on the bottom. That element is apparently live even when the ice bar is in the upper (off) position. When I unscrewed the old ice maker and went to lift it off the bolts, I severely burned my finger on the bottom of the old ice maker because apparently I started the repair in the middle of the heating cycle.
I highly recommend that you unplug the ice maker entirely before doing the replacement and gingerly ensure that the unit isn't hot before touching it. You'll save yourself a nasty burn.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anil from Somerset, NJ
- Parts Used:
- 5303917954, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Refrigerator was not cooling and the motor was running constantly
Having tried PartSelect.com before, I was very comfortable with the process. Input my symptoms and the feed back I received was that one of the 2 things (Defrost Timer or Defrost Thermostat)might need replacement. Since the cost was not much and over night shipping would cost more than the product, I decided to order both the parts. Changing parts was a breeze. The instructions posted by others on your web site were very easy to follow. You guys save me a bundle every time I have any thing going worng with any of my appliances.
Was this instruction helpful to you?
Thank you for voting!
Replace the storage drawer supports and Tank Support Stud
Used pliers to remove and install tank support studs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colline from PENDLETON, OR
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker not making Ice
Unscrewed (loosen) screws lifted unit out unplugged electrical connection. plugged in unit hung on screws tightened screws and had ice in less then 1 hour. Rick
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carol from woodland, WA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the freezer would stick in defrost and not come out
Removed the vent cover at the bottom. Removed the screws. disconected the harnes and put the new timer in. This was a very easy fix. Thank You!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- colleen from salt lake city, UT
- Parts Used:
- 5303918277
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench (Adjustable)
ice machine was now working correctly
watched the video (VERY helpful) and then removed the old icemaker and replaced it with the new one. Difficult only because of the small working space in the side by side freezer plus you can't see what you're doing when you tighten the screws. Working like a charm now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Pinole, CA
- Parts Used:
- 215846602
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Frost in freezer, fridge not cold
From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Lake Luzerne, NY
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
first fresh food too hot, then freezer too hot
Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done!!! Couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arand from Yorktown, IN
- Parts Used:
- 5303288973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The original support was broken, tried epoxy and it only held for a few months before breaking again
All I had to do was remove the original support that was on the inside wall of the refrigerator, which I had to use pliers since there were broken pieces, and then I just snapped the new one into the three holes provided for this support. The crisper drawer works fine now. It literally only took about 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from GILBERT, AZ
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
made lots of noise
Loosen two screws, unplug power, lift it off, put new one on and make sure water chute is correct place, tighten screws!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from WETUMKA, OK
- Parts Used:
- 218147701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
storage drawer frame had cracked in the back
Simple, removed old frame, took off the humidity slide control and installed on new frame. Slid it back in place. Great service, had it the next day, thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Seal Beach, CA
- Parts Used:
- 215267701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
end piece broken that held bar on freezer door shelf
attached the bar to the end piece and slipped it into the proper opening. Easy I ordered the piece one morning and received it the next morning. Great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from State College, PA
- Parts Used:
- 5303289501, 218147701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drawer and rails broke due to under design of the components
This was the second time i replaced the drawer and the first time for the frame.The repair was simply removing the old frame from the refrig and removing the rollers from the frame with screw driver. The rollers are reused with the new frame.The frame was reinstalled in the refrig.
The replacement of the drawer requires reusing the drawer front which is easily removable. The only complication with drawer repair was the need to trim some flashing that was not removed after the molding process at the factory to allow the drawer face to fit properly on the new drawer.
this problem is a quality control issue with the manufacture of the storage drawer.
The replacement of the drawer requires reusing the drawer front which is easily removable. The only complication with drawer repair was the need to trim some flashing that was not removed after the molding process at the factory to allow the drawer face to fit properly on the new drawer.
this problem is a quality control issue with the manufacture of the storage drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from ROADBURNS, TN
- Parts Used:
- 5303289500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Shelve pan broke on side
Removed old pan and cleaned all surfaces and reinstalled new pan.
Was this instruction helpful to you?
Thank you for voting!