GLHS66EJW0 Frigidaire Refrigerator - Instructions

I just pulled the old gasket out , pressed the new one in with my thumb,and was finished. thank you, Langley

I removed the old gate by using a flat head screw driver to pry open mouth. I then removed 2 bolts that held on the cage that hols the ice crushing blades. Then I inserted the new gate and used a screw driver to pry the mouth open again (it was more difficult to insert than remove). I then popped in the new gate and re-assembled the cage. It worked on the first shot with no problems!

This is the 3rd time I have attemped and successfully repaired major home appliances myself after the warrenty ran out. I'm sure I could buy a new appliance for the money I saved.

Took off old gasket and pressed in new one. Took about 5 minutes for both procedures. Vey Easy!

I shut the water off under the sink and removed the back piece on the refrigerator, unscrewed the water valve, cut the ends off each plastic hose and reinserted into the new water valve. Then rescrewed the water line into the new water valve and turned on the water. Unfortunately, I was not able to get water out of the door and the ice maker still doesn't make ice. While this was an easy procedure, it didn't help me. I'm not sure I needed to replace the water valve.

The shelf bin is a piece that anybody can clip it on the door in less than 30 seconds. No tools required, just simple common sense.

I located the part that was the culprit as it had buzzed very much before quitting. This is an easy removal as the part is in a two prong jack and just needs to be carefully removed with the new part inserted back in the jack provided. The refrigerator works fine now, but the run capacitor will still buzz on start up of the compressor. I do hope this is normal in this model? anyway it runs fine mow. Thank you.

A plastic guide rail broke after the meat keeper drawer was left open and the refrigerator door was shut on the drawer, this has happened a few times over the last 6 years. We chose to change out both rails at the same time. We removed the meatkeeper drawer, then the shelf above as the rails are attached to the shelf. We removed the rails (one screw on each side. When the new rails came in, we replaced them with the screws. Super easy!

Went the typical route of part replacement since I don't own an ohm meter...pull and replace one part at a time. Started with the cheaper parts first, replaced the freezer fan for $40, same problem. Replaced the defrost heater element for $40, same problem. Replaced the thermostat $15 and controller board $150 at same time, bingo problem solved. Had to defrost with the hair dryer each time, biggest pain. Had an issue finding a Utube that showed the water filter system and thermistor removal for this model, otherwise straightforward, but not a 30 minute job.

Unplugged fridge from outlet. Removed rear panel on freezer side. Removed defrost thermostat from tube and cut wires. Installed new thermostat by matching color coded wires and crimping with supplied connectors and snap back on tube. Reinstalled panel and shelving.

Silly me. It couldn't possibly be the filter because it's worked for the last 9 months with no problems. Decided to replace the water filter base first. Repair was easy. I saw someone had trouble removing tubes from old base and I gave it a couple of tries to no avail so decided to cut the lines instead. Made it even easier. After repair, water continued to leak. So, replaced the filter itself and voila - leak fixed. Make sure you check the filter first. My mistake turned a $40 - 10 second repair into a $100 - 20 minute repair. Good Luck!

Unplug refrigerator. Take out spill tray by sliding out. remove bottom 3 screws, gently but firmly push up and against refrigerator(Top section of cover snaps in by pulling cover down while holding cover against refrigerator). There is a ribbon wire connecting the two boards, care not to tear it out of connectors. There are two tabs on the plastic connector holding the ribbon wire to the outside board,pull the tabs out a little and gently pull the ribbon loose, carefully. There are 3 screws holding in the back board, remove them, them remove water hose from water actuator so the assembly can come out. Gently spread the plastic holder to be able to take the broken paddle out. Watch closely how the third arm on the actuator(Lower left arm)is resting on the back of the flapper.Replace the Actuator exactly the same. Just reverse the steps to install the rest of the parts.(Had a time getting the water hose back into it place. I used pliers to push and wiggle it back into it opening).Don't forget to plug the frig back in again. DOOR CLOSING CAM AND HINGE BEARING ARE VERY EASY. It take about 10 to 15 minutes to do. Empty door drawers before procedure the screw holding the plastic cover, remove cover. I used a 3/8" nut driver and my cordless drill to take out the two lag bolts holding the top hinge.Lift door off bottom hinge. Replace Door Closure/Hinge Bearing. Reverse procedure to finish installation.

Removed stuff on door, removed 2 screws on top of door, lifted door off replaced one door closure/hinge bearing and one door closing plate and put door back on and wala no more thump.

One of the bins on my freezer door had the tabs, that hold it on the door, broken off. I orginally ordered the wrong item, but I called right away and Parts Select had the correct item to me immediately. It was a very easy fix, I just had to snap the bin in place once it arrived.I am very impressed with PartSelect and their service. I would definately use them again and recommend them to others.

First I removed the door. Took off the broken parts and replaced them. Easy and fast to repair.

I ordered the complete part and installed in about 10 minutes. The order went very fast, part was in stock and everything went very smooth. PartSelect.com was very easy to work with and they have a very satisfied customer. I will definitely use PartSelect.com again. Thanks for the great service