FRS22XGCD1 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Naugatuck, CT
- Parts Used:
- 218720500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
No water being dispensed
Pulled out the refridgerator and the valve is in the lower left corner. Disconnected the 2 electrical connectors, remover 2 screws with nut driver, removed 2 water lines. Install in reverse order. Works wonderful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Rochester Hills, MI
- Parts Used:
- 5303289500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rails broken on the upper storage drawer
The repair was extrememly easy and took about as long as it did to order the pasrt online. Just removed the front drawer handle with a screw driver ,slide it onto the new storage drawer and reinstall. Less than 5 minutes.
C.J.
Rochester Hills,MI
C.J.
Rochester Hills,MI
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from KEYSTONE, IN
- Parts Used:
- 5303918277
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker leaking, then would'nt shut off.
Ice maker is held by 2 screws just above the unit, on the wall of the refrigerator. You can't see the screws, so borrow your wife's makeup mirror. Shine a light into the refrigerator, and using the mirror, locate the two screws, holding the unit in place, on the wall of the refrigerator. Using a nut driver, or socket wrench, with a 1/4 in socket, loosen up the two screws, but don't remove them. Bump the unit upwards, and away from the screws. (BEFORE doing anything!! Shut off the water supply, unplug the refrigerator) When you get the unit freed up, just unplug the old unit, and install the new one. You don't even have to worry about the water lines, and you'll see why, when you get the old unit off. Just reverse the procedure, installing the new unit. Very Simple, 10 to 15 minutes tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from GROTON, CT
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker stopped working. Part needed to repair it no longer available so had to replace the whole icemaker.
Loosened the two mounting screws (no need to remove them), lift off the icemaker and unplug it. Reverse the order and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ludy A from Midwest City, OK
- Parts Used:
- 5303289501
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Side rails broken
Removed old drawer, removed front pannel. Installed front pannel on new drawer and reinstalled ing fridge
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Ardmore, OK
- Parts Used:
- 5303289500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drawer cracked
no problems
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from KNOXVILLE, TN
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker would dump ice one time and then stop. Turning the ice maker off for a minute and back on would repeat the process.
I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.
It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.
It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from KERRVILLE, TX
- Parts Used:
- 5303918277
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Stopped making ice.
Had to reach right hand to top of ice maker to locate hex head screws by feel, then place nut driver onto hex head by feel and then unloosen screws with lft hand ,a couple of turns, enough to lift ice maker off screws.
Replace new icemaker onto screws and tighten screws. The only problem incountered was the location and availability of having to feel with both hands to fit nut driver onto the screws.(could not see with my eyes because front of ice maker blocked view. )
Replace new icemaker onto screws and tighten screws. The only problem incountered was the location and availability of having to feel with both hands to fit nut driver onto the screws.(could not see with my eyes because front of ice maker blocked view. )
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Bridgewater, NJ
- Parts Used:
- 5303918277
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
No Ice !
Real simple repair..just backed off the two 1/4" hex bolts holding the ice maker to the wall of the fridge,(a little tricky since you can't see them),unclipped the electrical doo hickey. I re-clipped the electrical do hickey of the new ice maker, hung the ice maker on the bolts and then re-tightened them. However,still no ice,my problem was the water valve on the back of the fridge behind the cardboard. Although it was still giving H2O thru the door it was not allowing water to flow to the ice maker. I reccommend pouring some water into the ice tray of the ice maker. If it makes ice and dumps it in to the holder, your ice maker is OK. If it turns out to be your water valve, that fix is easy as well. I HIGHLY reccommend watching the "fix it" video associated with that part. That repair also took less than 15 minutes. Good Luck! KC Bridgewater,NJ
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chester from Oak Lawn, IL
- Parts Used:
- 215501901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fan not running.
removed old fan and replaced it.3 screws and plug.Always unplug appliance when working on it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from GIBSON CITY, IL
- Parts Used:
- 5303289501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Drawer was broken.
We moved the refrigerator out so the drawer could be removed. (It was close to the wall) After removing the drawer the front of it had to be removed, then put on to the new drawer. The hardest part was that replacement because we had trouble getting it lifted up. Then the drawer was put in, refilled, and refrigerator moved back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Art from Bullard, TX
- Parts Used:
- 5303289501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Poor design resulted in lower crisper drawer breaking on both sides.
Got the new drawer 2 days after I ordered it. Snapped the front off the old drawer and onto the new one, and slid the new drawer in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Wichita, KS
- Parts Used:
- 5303289501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the slider broke on the drawer and couldn't move in or out.
front of old drawer needed a little persuasion at coming off, but once I figured out all I needed was a small screw driver to seperate the front from the drawer, it slid right off. Was a simple fix and a lot less than calling service repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PERRY from LOWER BURRELL, PA
- Parts Used:
- 5303918277
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice Maker Stopped Making Ice
Removed power , unplugged wires and 2 screws then reversed the process 1 hour later first batch of cubes dropped into bin
Was this instruction helpful to you?
Thank you for voting!