FRT21LR7AB7 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Benjamin from Jersey City, NJ
- Parts Used:
- 5304507147
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
The refrigerator door did not come for the opening swing to be reversed
I ordered four bearing hinges and drill holes for the hinges on top and bottom of frezer and fridge doors insert the bearing hinges on the holes and all the other part on the door were able to reversed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice M. from Washington, DC
- Parts Used:
- 240505801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door Would Not Close
I stuck a small screw driver under the old switch & it came out really easy. I just unplugged the 2 electrical connectors, and removed the old switch. Installing the new one was just as easy. I am a woman!
I also want to say how FAST PartSelect gets their items to you. It came in ONE day!
Your repair stories are very helpful, I/we would have never known how easy this switch was to replace! Thank you!
I also want to say how FAST PartSelect gets their items to you. It came in ONE day!
Your repair stories are very helpful, I/we would have never known how easy this switch was to replace! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Lakeville, MN
- Parts Used:
- 240505801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light switch did not operate correctly
Piece of cake! The new part just plugged in to socket and back into fridge frame. Appreciated how easy it was to order this part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Les from Fenton, MO
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Freezer icing up and refrigerator section not cold
Removed four screws for cover on refrigerator temperature controls, unpluged old timer and pluged in new timer. Replaced cover and screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from PUEBLO, CO
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Drive great stripped for ice eject. Heater bad
Loosened the 2 bolts 4 turns where it mounts inside the freezer. Lift maker off the bolts unplug 1 plug. Reverse to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JUSTIN from NEW BRAUNFELS, TX
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Top cools bottom is weak
Unplug, remove 2 screws off back panel inside the freezer. Cut wires on old one and crimped in new one. Light to melt the shrink wrap that came with it. Pretty easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from IVYLAND, PA
- Parts Used:
- 5304458371
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Over a few days duration the ice maker stopped producing cubes , after a basic examination of the unit I found a web site that provided parts and instruction on self repair .
so basically if you can make toast , you can do this repair....loosen 2 hex head screws ,lift up on the ice maker and separate from wall of freezer , unplug the wire harness ,it is now OUT , swap the water level indicator to new part [30 second job ] Install the new part in reverse order as mentioned above... enjoy your ice
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leah from Tecumseh, OK
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
After installing new ice maker water was not running into the ice maker.
Shut off water supply under the sink. Removed old valve and installed new valve. Turned water back on and within a couple hours the first batch of ice made.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from KEYSTONE, IN
- Parts Used:
- 5303918277
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker leaking, then would'nt shut off.
Ice maker is held by 2 screws just above the unit, on the wall of the refrigerator. You can't see the screws, so borrow your wife's makeup mirror. Shine a light into the refrigerator, and using the mirror, locate the two screws, holding the unit in place, on the wall of the refrigerator. Using a nut driver, or socket wrench, with a 1/4 in socket, loosen up the two screws, but don't remove them. Bump the unit upwards, and away from the screws. (BEFORE doing anything!! Shut off the water supply, unplug the refrigerator) When you get the unit freed up, just unplug the old unit, and install the new one. You don't even have to worry about the water lines, and you'll see why, when you get the old unit off. Just reverse the procedure, installing the new unit. Very Simple, 10 to 15 minutes tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from Catskill, NY
- Parts Used:
- 240338101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door shelf broke.
Very easily did the repair -- popped the new door shelf right in the place of the old one! No tools needed, no hardware, easy! The part actually measured 24 3/4 but the replacement part said "26 inches" on website & this was THE replacement part. Put this off for so long--ordered part and recd within 2 days, great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Lancaster, CA
- Parts Used:
- 240313703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The original part was plastic/and broke
unscrewed to little bolts and installed the new/metal part we got rfom partselect.If we may say.this is a great company to buy from! Fast!
Was this instruction helpful to you?
Thank you for voting!
Bin door has never been secure. It falls off every time we open the door.
Did nothing. The old bin had been repaired so many times just trying to make it stay in place that we threw the old one away and bought a new one. While at it, I looked to see if I had room for another shelf bin. I simply snapped it on too. The new door bin that I purchased does not stay on any better than the one I replaced. My summation would be that the little clips that protrude to hold it on are either too rounded and it slips off or they are simply not long enough. One bump and this bin is in the floor along with it's contents.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Montague, MI
- Parts Used:
- 242193211
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
moved into a new home and the inside freezer was iceing next to the freezer gasket.
purchased a new freezer gasket. It is still iceing in the freezer but now all over the top part and down the back. The new gasket does not secure tight enough around the entire freezer door when it is closed. It is secured properly to the door but does not "grab" tight enough when the freezer door is closed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from KNOXVILLE, TN
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker would dump ice one time and then stop. Turning the ice maker off for a minute and back on would repeat the process.
I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.
It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.
It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.
Was this instruction helpful to you?
Thank you for voting!