FRT24TGCW4 Frigidaire Refrigerator - Instructions

Unplug refrigerator , loosing two screws. Lift ice maker up to remove from position. Disconnect electrical connection. Reverse procedure to install new ice maker.

Removed 2 screws that hold ice maker in place. Unplugged and took out of freezer. Used the screws I took out to put new ice maker in. Plugged in the power and in 2 days I had a full ice bin and haven't had any worries since. Should have replaced the broken one along time ago but thought that the process was harder than this. Very easy and suggest this to anyone having ice maker issues. Less than $100 and never have to buy ice for the house again.

Purchased a new ice maker assembly and installed. Very easy

Followed on line video. Also water supply tube on fridge was full of ice. You can pull it out and run hot water on it to clear.

I found that the fill solenoid for the ice maker was down to a drip when energized. I ordered from this site and replaced. now plenty of water, but the ice maker would just stall and jump teeth. The heater which heats the ice up to free it from the mold was defective. Ordered from this site, and now working great.this sitet has good pricing, and the help illustration is great, and explains the sequence of events. This made it easy to troubleshoot. This refrigerator has not give a problem in over 11 years. The problem is "the ice maker". I have replaced it 6 times.

A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.

removed ice maker storage holder and then remove two philip screws and unplugged four pin connector. removed ice maker and installed new one . very easy to do

The instructions that came with the replacement icemaker were very complete, in particular concerning the small levelling bracket on the bottom of the icemaker, because the old bracket needed to be removed from the old icemaker and transferred to the new one. This part of the installation might not have been obvious, so I was glad to see it clearly outlined in the instructions. The old icemaker was removed by loosening two nuts and detaching the electrical connector, and the new one was installed in its place. Fairly simple, the whole job took about 45 minutes because I work slowly and carefully. A more confident person could probably have the new one installed in 15 minutes. Only drawback: about three to four weeks after installing the new icemaker it has begun making a loud clicking noise on occasions. It is a repetitive (5 second interval) clicking, and only happens for about a minute every few hours and then stops. I am concerned that it might be gears prematurely wearing out and slipping. I guess I'll know in a few weeks if this one stops making ice.********************************************* Update: after about 9 months the new icemaker quit working and will need to be replaced. I removed the front cover from the icemaker and could clearly see that the teeth of one of the plastic gears were worn out and no longer meshing with the opposite gear. The drive gear was just spinning in place and making no contact with the larger gear.

Pulled unit away from wall and shut off water and unplugged unit. Installed water valve and reassembled, plugged back in and turned on water and checked for leaks. All good. However there is no water getting into the ice maker. The unit itself is going thru a cycle of attempting to make ice and the bail is moving and you can hear the solenoid activate but no water. I have tried to blow thru the tube going to the maker but it seems to be plugged by something. I do not know if there is another valve up there or how to clean it out. Any help would be greatly appreciated.

I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.

Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.

installed new ice maker. Was very esay - the only problem I had was the length of the wire, due to the need to use the adapter, was hard to menauver around so that it didn't contact the bottom of the ice maker. Would be best if it was configured so that you had the right wire connection and didn't have to use the adaptor.

The service man that I hired to fix my Ice maker removed the broken one. This is how I saw how easy it was to install. When the new one arrived all I had to do was plug it in then tighten 2 screws with the right size nut driver. This was the hardest part of the install havng the right tool for the job. Now I have Ice!

The repair took only 5 minutes. I removed the ice bin, which just slides out, then loosened 2 screws at the back-top of the ice maker. I then unplugged the broken ice maker, removed it, put in the new one, re-tightened the screws and plugged it in. It was making ice within an hour.

Turned off water, unplugged refrigerator, Removed defective unit with support bracket. Installed support bracket, adjusted flow screw per instructions, plugged in wiring with adapter, hung on screws, tighened screws, secured excess wiring harness (making sure it did not hang below icemaker per instuctions), turned on water, plugged in refrigerator. Comment it took a few hours to start making ice, air in line? After a couple of days seems to be working fine.