FRS26ZGEW3 Frigidaire Refrigerator - Instructions

I could not believe just how fast my order came to my house! The drawers fit perfectly..just like the old ones.

I would highly recommend your company.

Thank you for having the right part for my refrigerator and the expedicious delivery of my order.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wiring harness plug, replaced the old timer with the new one, re-connected the wiring harness and reinstalled the mount in position. Hardest thing about it was lying on the floor.

the first purchase was the drawer support. that helped, but in the process of replacing the support, we noticed that the drawer was also broken. bought the drawer and a roller that we had inadvertently thrown away with the broken piece of the support.

used a screwdriver to replace the roller. delivery was terrific. the parts fit. nice job.

Removed four screws at top and two at bottom and pulled ice maker unit out and replaced with the new lever .

had removed the doors to get fridge in thru small doorway when doors were reinstalled the elbow leak was replaced in about 15 minutes or less by cutting old elbow out of lines and the lines snap into new elbow with just a little force

removed water tray, used a razor blade to brake the seal from the face plate and the fridge, The hardest part was the three screws holding the dispenser face place on where rusted over. I wound up drilling them out. Once the screws removed, a slight lift, the face plate comes right off. I unplugged the cable, and set it aside. Now remove the next three screws, and the dispenser falls forward, (as far as the water line allows) undo the screws leaving the one emplace to hold the ice lever. push up twist. The hard part is getting the new one up and in. just takes a little patients.

Turn off power. Remove ice tray. Back out the two screws with nut driver and just lift ice maker off screws. Do not bend the water fill tube in the back . Now unplug the wire and remove ice maker .
To replace, match the color of wires on plug. Adjust wires in place and water fill tube and back on to the screws. Hold in place and snug screws. Turn power back on. In 4 to 5 hours your ice will start .
FED-EX UT to MN was 13 days to deliver .

Removed broke bracket. Installed new bracket (part #100). Now, everything is O-TAY!

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

Replaced drawer slide, R&R two 1/4" hex head screws, 5 minute job. Door handles required phillips screw driver, simple once I figured out trick to upper and lower moulding re-install. Need to remove plastic clips from doors and insert into mouldings, then slide mouldings over new handle ends and snap into place.

Unscrewed the gaskets from the doors and took off. screwed the screws and put tthe sealant on t he cornors on both doors and that was it. very easy. directions were great.

Looked up similar problems and found it to be the defrost timer. All I had to do was remove the plastic portion in the fridge section to get to the old timer. Popped the new one in and put it back together. Works great now. Would have been almost $150 to have a repair company come out and fix it.

Looked it up on how to, follow the video
. Very easy 1-2-3 it was out and new one in..........??.

Removed parts and reused the old rollers from the sliding meat drawer. Important point to remember is to not through away any hardware before the new parts arrive. New parts are void of hardware. Parts arrvied ontime as promissed and fit perfectly. I saved a ton of money doing this myself and not calling the repairman. great experiance.

But I have back ground mechanical skills, I did see the video one time, and everything went smooth......