FRT18RRCW1 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lawrence from San Francisco, CA
- Parts Used:
- 218758602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The shelf end caps weakened with age and broke.
I removed the shelf, took off the old ends caps, replaced them with the new ones and put the shelf back in place. No glue or tools needed and the job was completed in under 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justine from Oxnard, CA
- Parts Used:
- 218971302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The tip of the braket broke and would not longer hold the meat drawer
First, my husband removed the shelf assembly. Then he unscrewed the boken bracket. He then screwed in the new bracket and proceeded to install thecomplete shelf assembly back into the fridge. Placed the meat drawer back into correct location, to fit back into rail brackets. All done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carol from woodland, WA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the freezer would stick in defrost and not come out
Removed the vent cover at the bottom. Removed the screws. disconected the harnes and put the new timer in. This was a very easy fix. Thank You!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Minneapolis, MN
- Parts Used:
- 215441502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Removeable shelf in refrigerator broke
Put the new shelf into position-Voila!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Grants, NM
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Defrost timer was not working
Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TIM from WOODBURY, TN
- Parts Used:
- 218906802
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The refrigerator light would not work ...even after replacing the bulb.
I used a flat head screwdriver to pry open the front of the socket as I pushed the socket toward the freezer side. I unplugged the two wires connected to the socket then re-connected the two wires to the new socket and popped the new socket back in. I then put a new light bulb in and we had light again in the fridge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JoAnn from Newark, NJ
- Parts Used:
- 215441502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed the door bins to hold more items.
Just took it out of the box, wash it and put it on the inside door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Lonaconing, MD
- Parts Used:
- 218724000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
front roller assembly was missing/holes stripped
Unplug fridge, tilt back against wall to provice clearance to install new assembly. Used self starting screws to install. Used cordless drill with nutdriver to install assembly.
Time to complete job-5 minutes
Time to complete job-5 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RODNEY from NEW YORK, NY
- Parts Used:
- 218971202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic rail broke.
The meat drawer is already pulled out because the broken rail could not support it. 1st I removed the shelf. Then I removed the 2 screws connecting the rail to the shelf. I then replaced the rail, screwed it together and put the shelf back in place. I put the meat drawer back on the rails and it's done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- earl a from GIRDLER, KY
- Parts Used:
- 218906802
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light blub blew
unplug power from ref removed old light socket only difference wired a little different checked new socket compaired to old checked terminal ends small big looked at wires big,little plugged up put in new light blub plugged ref power back on work power off pushed socket bac in power on works
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Bay City, MI
- Parts Used:
- 5304464438
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Fridge quit working.
A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Spokane, WA
- Parts Used:
- 5303917954, 215846602
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Temperature in both freezer and fridge sections to warm!
Dear Part-select,
I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 part if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work
Tom Houck
Spokane, WA
Houck Photo
509-723-3418
tomhouck1@comcast.net
I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 part if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work
Tom Houck
Spokane, WA
Houck Photo
509-723-3418
tomhouck1@comcast.net
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Sunnyvale, CA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
No freezing or cold in either freezer or refridgerator - compressor did not run.
Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessica from Lincoln Park, MI
- Parts Used:
- 218758602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer door shelf retainer bar kept falling off
I removed the retainer bar from the freezer door and unclipped the broken end cap (the clips were broken). I snapped the new one into place and snapped the retainer bar back into the freezer door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Eatonville, WA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Defroster didn't work
Ordered a new defroster timer and replace old one. It works just fine. A $35 repair vs a $500 new appliance.
Cool.
GWE
Cool.
GWE
Was this instruction helpful to you?
Thank you for voting!