FRT13CRAD0 Frigidaire Refrigerator - Instructions

I followed the procedure online and found the thermostat was ok, it had continuity when cold, and the heater coil was also ok, it too had continuity, therefore the problem was a bad defrost timer. the refrigerator works great, thanks parts select!

Snapped new caps in place . Took about 30 seconds!

Problem not consistent. OK for 2-3 weeks, then freeze coils. Mark and observe the defrost timers manual rotating adjuster. Timer would stop mid cycle. One revolution equals 8 hours of compressor run time followed by 30 minutes of defrost. Replacing timer took 5 minutes.

I used a pick to remove the lugs from the old starter. Clicked them right in the new one and it went to woking!!!

I first thought the defroster heater broke - took the back wall of the freezer off and cooling fins were fine. Then took the defroster timer out and opened it up. The contacts were badly burnt so the compressor and fan ran during only part of the cooling cycle. Replacing the timer took less than 5 minutes - turn off the power, remove one screw to take out the control box, cut the ground wire (new timer housing is plastic and does not have a ground connection), remove two screws to unmount the timer, unplug the old timer, plug in the new timer, fasten with two screws, put the control unit in and fasten with one screw, turn power back on.

This poor frig.(purchased in 1984) has gone thru five military moves. Somewhere along the line the plastic tabs to the door shelves broke, but I retained the metal bars. I hoped to find the required plastic ends to fix them and you had exactly what I needed. The repair was so fast and easy. The amount of pressure was a bit more than I originally thought was needed but they all went in perfectly.

Unplugged the frig. Removed temp control module from frig, 1 screw with nut driver. Activated defrost timer by rotating adjustment until 2 clicks are heard. Removed two timer mounting screws, unpluged timer, plugged in the new timer, mounted it to the control module with 2 mounting screws. Replaced control module with the 1 mounting screw. Closed door and plugged it up.

I went on partselect put in make and model number, a list showed the probable cause. I watched the how to video. When I received the part in short order I loosened 2 screws disconnected the wiring plug (sprayed it with contact cleaner) pluged it in, removed screws from old part put them in new one. Put timer back in its location and tightened the screws. Very eazy, works fine.

I pick up very fast at these kind of small jobs but because of my very busy schedule I decided to call (2 times) technicians about my problem but none of them had any idea. About my repair, I removed the grill at the bottom of the refrigerator, unscrew a small plate (located on the bottom left side) that's holding the defrost timer. I plug on the new part, screw back the plate with the defrost timer and that was it. Don't forget to turn clockwise with your finger the timer until you hear a "click" and then turn it slightly more to the right. There is also a video on U-tube.

Simply snapped ends into shelf and snapped into the fridge door.

open freezer door two screws just below unscrew slide piece to side unplug reinstall very simple.

Ordered new parts, removed old parts, put in new parts. Done.

Part Select suggested probable causes and supplied videos of how to make the repair of a 25 yr.old refrigerator along with the specific parts to order. I was about to trash the old refrigerator but after replacing the parts for a total of about $40 and 1 hour of time it works fine now.

The instructions given to me by part Select were very good.I replaced the Timer- checked the heater with oham meter it was good- checked the door weather striping it was good and replaced the thermostat with new .So at this point I may need to call a professional unless some one has another solution.

1. Unplug the refrigerator.2. Remove the storage rack and back panel in the freezer. 3. Locate the thermostat. 4. Defrost the freezer coils , i used a hair dryer. 5. Remove the thermostat from the cooling coil and then clip the connecting wires close to the unit. 6. Strip the ends of these wires and connect these wires to the wires of the replacement unit using the supplied wire connectors. 6. Heat seal with a lighter the connections using the water shield sleeves provided and further wrap connections with electrical tape. 7. Reconnect the thermostat to the cooling coil at the location it was removed from. 8. Replace the freezer back panel removed earlierand the storage rack if you have one. 9. Plug the freezer back in. My refrigerator has been working ever since the repair. There are several YouTube videos available that walk you through the diagnoses and repair process. They are very good.