FRS23KF5DW2 Frigidaire Refrigerator - Instructions

Test the light socket first with a bulb that you know is good. If the light still does not come on, unplug the refrigerator, remove the switch by inserting a very small, thin, flathead screwdriver alongside it and pull the switch out slowly with your other hand. There are two wires there. Remove them gently with some needle nose pliers. If you want to test to see if the switch is defective, take a insulated jumper wire, and attach it between the two wires. Plug the refrigerator back in and see if the light comes on. If the light does come on, replace with a new switch by re-attaching the wires and placing it back in the hole firmly.

Unpluged the item. Turned off the water source. Removed the card board cover. Dis-connected the water hoses. Unpluged the connetors. Matched up the colores and put it back together, very easy. Everythings was color coded.

Just pushed the button along side the filter and it popped out in my hand. I unpacked the new filter module and inserted it. It was necessary to run water through the dispenser for a couple of minutes to purge the air and clear the lines. The modular filter assembly is more expenseve than some but the ease of replacement makes the cost a good value.

Removed (unsnapped) plastic cover from back of refrigerator ( inside freezer compartment), determined that the fan was not turning, removed 4 screws from the aluminum back plate in freezer and tilted it down. Removed 2 screws with a nut driver, this allowed the fan to be removed, unpluged fan motor from the bace of the freezer and removed fan. Installed new motor and spent $38.00 to repair the refrigerator that would have cost me severial hundred dollars to replace. Thanks for the help

First I unplugged fridge. I then removed cover that keeps fan protected. I then removed 2 screws that hold the evaporator motor in place. I then removed 3 wires running to motor. Very easy to remove, just pulled connections apart. I then replace the old motor with new.

The Sears repairman wanted to charge me $359 to repair. I did repair for under $40! Amazing what you can save if you have the time and knowlege to do it yourself.

I shut off the water supply and removed the 4 screws from the cardboard back revealing the water valve. I removed the 2 screws which attach the valve to the refrigerator and removed the water valve. Once out it was a snap to unplug the electrical leads and unscrewed the water lines, Insalling the new part was a matter of reversing the above procedure. Everything is color coded which made this replacement extrememly simple.

I will definitely use you guys in the future. The ordering process was great and delivery time was ultra quick!
Thanks for an easy part replacement and simple install.

Snap out fan cover, remove four 1/4" screws, remove back cover, remove defective fan motor, remove fan blade, install new motor and blade, strip wires and hook up with wire nuts, reinstall back cover, snap in fan cover, and plug in fridge.

most importantly on the page with the necessary part..cripser support for the refrigerator--- there was a brief insructional video on how to properly dislodge the broken part and replace it with the new showing the simple tools needed. I am not handy at all but it took me all of two minutes thanks to the helpful video.

first i by passed the timing board, with a ele cord to the fan motor to keep the fridge cool till your parts got here, which was realy fast delivered,
the fan would come on because the board was fried.
it took abot 30 min to install every thind just be carefully unpluging anything.things will break i guess metal eing cold makes the conne4ctors stick together.
evaporator fan is in the frezzer four screws,tested the wires for ohms,and power, when i pluged in the fan i would loss power to the fan,that told me the board was bad, the same night my furnance when to (reaaly) and i lost my borad on the computer ethernet card (lighting isn't fun) it cost to fix everything about 130.00 thanks for thr great parts

Just opened the filter storage and popped out the old one and put in the new one. Ran the system for three minutes according to directions and it worked fine.

Replaced ice actuator.

Tried replacing water filter first. It stilled leaked, so I removed the covers to gain access to the water filter base. After cutting the two hoses to remove the old base, I simply slid the hoses into the new base, screwed it into place, replaced the covers, and then reinstalled the new water filter. No more leak!

- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.

open refrigerator door unsnap & remove old bin. then just snap new bib in place. very simple.

I checked the dampener, it worked. The compressor and fan worked. I knew because my freezer was still hovering around 10 degrees. Coils were clean. Thermistor was the only thing it could be. Took all my shelves out. Removed four screws. Took the back panel off. The thermistor sits tucked in on the side. I piped it out, in clipped it. Used my multimeter to test the numbers. Numbers were off just a bit. Ordered the part. Crossed my fingers.,took less then 5 minutes to put the part in. Plugged in the fridge. It was sitting at 33 degrees in about an hour and a half. I can’t believe I fixed it. I knew NOTHING about refrigerators. For how big my fridge is, it would have cost 3,000 and up to get a new one with the same cu ft size. Instead, it cost me $44. That includes shipping. Thank you Parts Select!! Made it so easy to pick the correct part for my model fridge!