FRT21HP5AB0 Frigidaire Refrigerator - Instructions

Removed (unsnapped) plastic cover from back of refrigerator ( inside freezer compartment), determined that the fan was not turning, removed 4 screws from the aluminum back plate in freezer and tilted it down. Removed 2 screws with a nut driver, this allowed the fan to be removed, unpluged fan motor from the bace of the freezer and removed fan. Installed new motor and spent $38.00 to repair the refrigerator that would have cost me severial hundred dollars to replace. Thanks for the help

First I unplugged fridge. I then removed cover that keeps fan protected. I then removed 2 screws that hold the evaporator motor in place. I then removed 3 wires running to motor. Very easy to remove, just pulled connections apart. I then replace the old motor with new.

The Sears repairman wanted to charge me $359 to repair. I did repair for under $40! Amazing what you can save if you have the time and knowlege to do it yourself.

Snap out fan cover, remove four 1/4" screws, remove back cover, remove defective fan motor, remove fan blade, install new motor and blade, strip wires and hook up with wire nuts, reinstall back cover, snap in fan cover, and plug in fridge.

- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.

first i removed the four screws that hold the shelve in place disconnected the wire replace both diffuser-air,reconnected the wire and replaced the screws

Bought a new
capacitor.

Removed the cover inside the freezer. Found out that the motor/fan was not working. Ordered through PartSelect. Got the parts in 3 days. Installed it for less than 30 minutes. Very easy. It saved me hundreds of dollars. We considered buying a new fridge but not anymore. , it only cost me $70 including shipment charges. (Make sure you unplug the appliance first before opening the cover. Remember safety first.)

It was fairly easy. Only had to remove the back cardboard. Remove 3 screws and the power plug.
Replacing the screws took a little time the motor mount didn't seem to be tapped exactly for the screws supplied and it was in a tight area. Its working great now.

This was a simple job. Raised the flap in the back that houses the compressor, removed the wire that holds the relay, pulled out the old relay and pushed the new one on. Replaced wire holder and that was it. Plugged it frig and freezer is at zero and lower compartment at 35. As easy as brushing your teeth!

Took the old ones off and installed the new ones. Simple repair

I slid the new glass in place

My 4 year old grandson used the frig door as a swing.The bottom hinge cracked, then the door wouldn't seal. I propped the door up with some books, removed the broken hinge (2 bolts) and replaced with the new part. Simple fix on the door, only time will fix the 4 year old!

Pull out the shelf and remove the one screw that holds the support rail in place. Remove broken rail, slip in the new one, then replace the screw. Done!

It takes longer to remove items from shelf and clean it than it does to replace the part.

I unscrewed the old rails and took the number to order on the first day. The order came on the 3rd day. Can you imagine such fast service.
My daughter is a single mom with 4 children, one of whom was responsible for the breakage. I am the grandmother and was very grateful for the fast service and great price. The drawer was installed in 10 minutes. I just screwed the old screw into the new part and replaced the drawer. Thanks

I located the part that was the culprit as it had buzzed very much before quitting. This is an easy removal as the part is in a two prong jack and just needs to be carefully removed with the new part inserted back in the jack provided. The refrigerator works fine now, but the run capacitor will still buzz on start up of the compressor. I do hope this is normal in this model? anyway it runs fine mow. Thank you.