FRS23KF7AB0 Frigidaire Refrigerator - Instructions

Reviewed the video on your website and followed the directions to the letter. Great video

Turn off power to refrigerator. Remove dispenser tray and three screws. Lift up on cover and pull away from fridg. Next remove control circuit board, use magnetic screw driver on very small screws. Important to mark all wires and their location before removing. Remove water tube from water actuator by lifting tube out of actuator,you don't have to turn water off. Next remove dispenser module and set next to new dispenser module. Then carefully remove and install parts on new dispenser module. Take your time and besure all parts installed as they were on the old module.

This issue was noted in the advice area as being a filter, or valve assembly. But it turned out to be a diode kit that was causing this issue. I don't know why I could not find this issue anywhere on line? When I received the diode kit there was instructions that noted exactly the problem I was having.
The fix was easy just a few wires cut and spliced and viola fixed.

1. Remove outer plastic face cover (4) screws.

2. Revove (1) U type nut keeper & (1) metal washer.

3. Remove (1) plastic nut on end of metal auger.

4. Remove inner plastic cover (4) screws and disconnect control rod. (Note postion of control rod befor disconnecting)

5. Note position and order of metal blades and plastic spacers on auger before siding off the end of auger to reposition them upon re-assembly.

6. Remove metal support panel from end of ice bucket (4) screws.

7. Remove auger & plastic cylinder from ice bucket.

8. Remove - slide drive blade off auger.

9. Drive blade replaced.

10. Re-assembled other items removed in reverse order

This was really simple, much like changing a light bulb. Two bolts loosened beneath the old unit to allow it to be lifted off and free. The power supply plug was easily disconnected. The new unit was then placed onto the loosened bolts, power supply reconnected and secured with the supplied wire tie. A small angled bracket was removed from the old and reattached to the new as a support toward the from of the unit. The cycle adjuster was backed off a 1/2 turn as per the instructions....and the next morning....new automatic ice. Life is good!

Removed 4 screws holding face plate onto ice bucket. Removed the 3 screws holding the ice crusher housing. Noted postion and rotation of teh s;ring loaded ice selecting rod. Removed broken crusher housing. Reveresed process for installion. Took for test drive. Operational...

Put in new hinges and two screws

The repair was easy. The problem was the lack of explanation. This may help other customers. I was told by the virtual trouble shooting system that about 30% of the cure was to replace the water filter and 70% was to replace the water valve. I did both and still had the problem. People need to be told why they have to replace the water valve. The reason is this. The valve has a very small leak in it that lets water continue to flow into the freezer compartment drop by drop. Eventually, this freezes and clogs the hole , so no water can pass and thus no ice can be made.In either your web site or another they stated that it may freeze up here, but there was no connection to the water valve.It seemed like it was another topic. Its very hard to see the frozen area, unless you remove it from the freezer area. I wish I was TOLD TO DO THIS, after i replaced the valve It would have saved me a repair bill. I hope this helps others.
Take care-Bill

Unscrewed the water line cover. Removed the platic case around the water filter base. Everything went well until I tried to remove the two water hoses. After I finally figured out that I had to push in the release washer while pulling the hoses out, things went well. Unfortunately it took several hours of wasted time and several searches on the internet to finally figure this part out. From there on out it went smoothly. Old base came out with two screws. Reversed process for reinstall of new base. Water hoses just slipped back into place and locked themselves in. Just takes a little patience.

i removed the 4 screws holding cover. removed two screws holding timer. unplugged timer. plugged in new one. reassembled.

I followed a gentleman's directions on your website, very useful I might add. It helped me replace all the broken parts with ease. I am a 33 year old mom of two. Anyone could do these repairs that I did. Thank you.

Unplug turn water off
Removed two screws with nut driver loosen one
Disconnected three solenoid valves
Disconnected four water lines
Plug tubing in, tighten one flare fitting
Reattach wires to solenoids
Slide under loose screw, replace two screws
Turn water on check for leaks plug in get a drink of water

I had already removed the ice maker by loosening the two screws with a 1/4" nut driver, in order to compare the design and style to the intended replacement for size and critical measurements. The replacement was almost identical. The wiring harness was 2-3" longer than the original, but after snaping the wire plugs together I simply curved the wire up and to the left to be out of the way. The hanging brackets are slotted and it was easiest to slip the back hanger over the head of the screw and let it slip down, then the front hanger was already to line up even though you can't see the screw with the ice maker in the way. I had to transfer an L-shaped metal bracket to the bottom side, matching the old assembly, and adjusting it to hold the bottom side away from the freezer compartment a little so it would hang level and secure. You have to snug the two screws with a screw driver or 1/4" nut driver by feel, since you can't see them with the icemaker in place. It took about 10 minutes to take out the old and another 10 to put in the new. We now have a full bin of ice, and the old plastic trays have been retired. I should have done this a year ago.

Loosen two screws, unclip electrical connection, remove ice maker, remove l shaped leveling piece of metal from old one, put on new one. Install in reverse order. Hint.. when loosening two screws, use a mirror

First, unplug the refrigerator since you're working with live wires.

Remove the 4 Philips sheet metal screws holding the plastic housing that holds the temperature control to the top of the refrigerator compartment. Pull the housing down then out since there is a tube on the housing where the water flows out the back of the refrigerator during the defrost cycle.

Remove the 2 Philips screws holding the defrost timer on the plastic housing. Pull the connectors off the old timer and attach them in exactly the same positions on the new defrost timer.

Attach the new defrost timer to the plastic housing with the 2 screws.

Reinstall the plastic housing, making sure the water tube is inserted into the back of the refrigerator wall.

Plug the refrigerator back in and you're done.