GLRT218WDWB Frigidaire Refrigerator - Instructions

Simply unscrewed cover on water filter and pulled old filter out. New filter comes with o-ring on filter. Simply reversed procedure and installed new filter.

My hand turned the water filter casing around until it unscrewed and then I put in the new water filter.
Screwed the casing tight and I was finished.

Turn off power. Remove ice tray. Back out the two screws with nut driver and just lift ice maker off screws. Do not bend the water fill tube in the back . Now unplug the wire and remove ice maker .
To replace, match the color of wires on plug. Adjust wires in place and water fill tube and back on to the screws. Hold in place and snug screws. Turn power back on. In 4 to 5 hours your ice will start .
FED-EX UT to MN was 13 days to deliver .

Unscrewed old bulb and put in new one

I emptied freezer side of unit, turned unit off, rolled unit away from wall, unplugged unit, turned ice maker water supply off, and took out the ice maker. I then took out old light and replaced it with new light. I then plugged in the unit, turned on the water supply, rolled the unit back in place, placed the ice maker back in the unit and turned the unit back on.
After two hours I placed the frozen items back in the freezer.

I remove the old fan by pushing it off the spindle toward the evaporator and put the new one on by holding it on the right side and guiding it on the spindle from the left side, very easy task

Looked it up on how to, follow the video
. Very easy 1-2-3 it was out and new one in..........??.

Looked up similar problems and found it to be the defrost timer. All I had to do was remove the plastic portion in the fridge section to get to the old timer. Popped the new one in and put it back together. Works great now. Would have been almost $150 to have a repair company come out and fix it.

But I have back ground mechanical skills, I did see the video one time, and everything went smooth......

It was real easy took the lines off one by one put them on the new unit one by one same with the three plugs than tighten new unit back on fridge.

I removed the housing at the top of the refrigerator compartment that contained the reefer light and temperature adjustment knob. This required a small nut-driver. Inside, I found the old defrost control, unplugged it, unscrewed it with a Phillips screwdriver, and replaced it with the replacement part. Then I replaced the housing to its original position.

Removed the housing with the light, 4 hexhead screws. This exposed the defrost timer, removed 2 hexhead screws, electrical connector and reassembled the unit.

Great resource and service, thank you.

Removed the screws on the piece holding the switch which is at the front of the ceiling of the refrigerator box. Removed the old switch and replaced it. Very simple repair.

Super easy fix! Used flathead screwdriver to start corner of gasket, then just pulled it out with my hands. Cleaned the track and surrounding area with a rag and some windex. Started in top right corner with new gasket and just worked my way around the door until it was fully seated in track. Done! Only thing I would do differently next time would be to start at the bottom when installing new gasket, just so I could have better sight and leverage at the end.

I watched the video on how to change the defrost thermostat. I removed the back cover inside the freezer then I pulled off the old defrost thermostat and then using a pair of wire cutters I cut it off and then bared a little of both of the wires and then slid the heat sherink and wire connectors on the existing wires and then slid the other ends of the wires into the wire connectors then crimped the ends of the connectors and then tried using heat on the heat shrinks but still used rubber electric tape over it. I clipped the new thermostat were the old one was and then reattached the freezer wall cover and plugged the refrigerator back in. 24 hours later I checked the temperature in the refrigerator and freezer and both are running a lot colder.