FRT22QGJW3 Frigidaire Refrigerator - Instructions

Followed video instruction and completed the replacement. I had to join the wires since the connector was a male plug to a make plug.

Remove front cover below door, remove 2 screws attaching the defrost timer to the refrigerator frame.
Unplug wiring harness plug from timer an install new one.
Remove metal cover in back of the freezer compartment. unpug the two wires going to the thermostat, remove the thermostat { thermostat is held onto the cooling coil with a clip} , remove thermostat and replace with new one

Ordered the Capacitor and the Thermostat Control. Parts were received in a matter of a few days, easy to install, but did not fix the problem. Had to call a repairman to fix the problem (compressor relay - this part not available to order for this model number with Parts Select). Will continue to use Parts Select in the future for other parts, but not happy that the actual part I needed was not available - had to use other methods.

Heard the snap of a short circuit followed by a burning smell around the refrigerator. Pulled it out, unplugged it and removed the back panel with a nut driver. Plugged it back in and when the compressor kicked on I saw sparks and some smoke at the relay. Unplugged and ordered new relay and the associated run capacitor in case it was also bad.
Removed the holding clip and the relay with capacitor easily came out with two wires attached. Removing the wires was done by prying with needle nose pliers with some difficulty.
Inserting the wires into the new relay was also difficult. If the position isn't just right it does not snap in. Once it is positioned correctly it makes a positive connection with not much effort.
Reassembled the capacitor, plugged unit into compressor, added retaining clip and plugged in refrigerator.
Compressor started up correctly. Note that as the refrigerator cools the compressor will shut off for long periods of time. This is normal.

Removed the vent cover at the bottom. Removed the screws. disconected the harnes and put the new timer in. This was a very easy fix. Thank You!

My brother completed the repair by replacing rack on door and also brackets. The support rack had to be cut to size and then put on overall no too bad.

I removed the shelves in the freezer, took out the five 1/4" screws and lifted off the cover. It was a simple matter of using a blow drier to remove all the ice, then unplugging the two wires and unclipping the thermostat from the upper cooling tube. Then clipped the new one on and reconnecting the two wires.

Works great!!!

All I had to do was remove the original support that was on the inside wall of the refrigerator, which I had to use pliers since there were broken pieces, and then I just snapped the new one into the three holes provided for this support. The crisper drawer works fine now. It literally only took about 1 minute.

Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done!!! Couldn't have been easier.

removed the screws/nuts; pulled the back panel off, removed the old thermostat (wires just popped apart) replaced the new thermostat (wires just popped back on) replaced the back panel and the nuts and TaDa!!

From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.

I removed the shelf, took off the old ends caps, replaced them with the new ones and put the shelf back in place. No glue or tools needed and the job was completed in under 2 minutes.

Removed the back panel in freezer compartment with the nut-driver. Then I cut off old thermostat connections, and spliced in new thermostat connections (repairman had already replaced defrost timer, and said not to trust connectors included on wires-they failed often). Then I snapped thermostat itself onto cooler coil. So far so good, fridge is running at 35-40 degrees a week later. Thanks Parts-Select!!!

Had to remove all screws on rear back cover of freezer inside, unplugged refridgerator, uncliped thermostat, unpluged thermostat. Replaced thermostat with new one in the same location, and let defrost fulley. Reassembled, pluged in, and tested. All was good. But I did also replace timer at first part of the repair so I suggest you replace both at the same time.

Put the new shelf into position-Voila!