WRS22WNHW2 Frigidaire Refrigerator - Instructions

removed all items from frig.. removed shelves, loosened one screw on each slide bracket and moved them down and out of the way of the rear panel....removed 6 screws in rear panel...removed all ice on coils with a heat gun...located defrost stat, replaced...crimped wires...re-installed rear panel and shelves! On left side of frig. in front bottom..located defrost timer..removed trim piece, loosened 2 screws....removed and replaced defrost timer...plugged in the frig. and it started!!!!

Had to reach right hand to top of ice maker to locate hex head screws by feel, then place nut driver onto hex head by feel and then unloosen screws with lft hand ,a couple of turns, enough to lift ice maker off screws.
Replace new icemaker onto screws and tighten screws. The only problem incountered was the location and availability of having to feel with both hands to fit nut driver onto the screws.(could not see with my eyes because front of ice maker blocked view. )

Part broke during normal usage. Removed ice/water dispenser face plates by drilling out rusted screws (original should have been stainless). Removed dispenser assembly to work bench. Stuffed paper towels in ice chute to keep heat from entering into freezer section. Tried to epoxy old actuator, but was unsuccessful. Actuator broken at it's weakest point. Ordered part number as identified in the parts breakdown. Received wrong part. The right part had to be back ordered. Repaired plastic areas out old rusted screws. Bought all new stainless screws. Received actuator after 10 days. Installed part in dispenser at work bench. Installed dispenser in reverse order. Problem solved. Note, care should be taken to remember the order of removing parts ot make sure the assembly does not bind the switches.

After disassembling, the thermal fuse I ordered were not and exact fit, I had to cut off the ring terminals, strip the insulation back and splice it in.
It works.

Called "local" repair warehouse and ordered part. They shipped the wrong part. Went on-line to Part Select and got the right part.

Top freezer took off the panel in freezer and melted the ice around coils and found the defrost thermostat and replaced with the new one. Just followed the instructions from your video on line. Freezer works just fine now. Refrigerator is 38 years old.

The repair went easily after watching the video, took me less than an hour to complete the repair.

Removed ice bucket from freezer. Remove ice. Remove 2 phillips head screws from the inside front of ice bucket, and 2 fromt the bottom front to remove the front cover. Remove the E clip and washer from ice crusher shaft. Remove 4, 1/4” head screws from ice crusher housing. Unclip the selector shaft from crusher door paying attention to position.Slide housing off of shaft and discard. Install new housing over shaft and install the 4 screws. Install selector shaft into door. Install the E clip and washer onto shaft. Install front housing with the 4 screws previously removed. Refill bucket with ice and install bucket back into freezing taking care to orient the ice screw shaft into the cog in the back of the freezer as well as the door selection shaft. Test operation.

I followed the instructions, my ONLY issue was about the Part 46 the Ice Dispenser Actuator Rod. The front of the arm has flared out grooves and it didn't warn me about making sure the rod is properly aligned thru part 23 Front Plate or else when the ice maker actuates the rod it will not move properly if the grooves are not aligned on each side of the Front panel. I hope you can understand what I mean, if not just look at how the Part 46 rests in Part 23

Removed power , unplugged wires and 2 screws then reversed the process 1 hour later first batch of cubes dropped into bin

front of old drawer needed a little persuasion at coming off, but once I figured out all I needed was a small screw driver to seperate the front from the drawer, it slid right off. Was a simple fix and a lot less than calling service repair.

A pretty easy, remove and replace, project. The spring that closes the fridge door had broken. Just pulled out the old part on top of the appliance and put in the new part. I noticed that part of the problem was that the bottem hinge needed a little lubrication too, as the door wasn't closing as easy as it should with the new part installed. I can't complain though, the side by side fridgeadaire is getting old and this was a very easy fix.

ordered new drawer, removed the clear plastic front piece from old one and installed on the new one. It was delivered only one or two days after I ordered it and was in perfect condition. Excellent service.

I found PartsSelect on the web, input my appliance model# and type and a very easy to read diagram of my appliance appeared. I simply selected the parts I needed from the diagram,and the part numbers were displayed. I placed my order and 2 days later the parts arrived, and I installed them immediately. No fuss, no problem. Great Service!

Got the new drawer 2 days after I ordered it. Snapped the front off the old drawer and onto the new one, and slid the new drawer in.