FRT21LR7AW2 Frigidaire Refrigerator - Instructions

I started look inside ,disconnected power, and open all possible compartments to see any burned part. Fortunately I fined a small part look like melted and then i went online and make my research .Then i ordered that part and change it.

Real simple repair..just backed off the two 1/4" hex bolts holding the ice maker to the wall of the fridge,(a little tricky since you can't see them),unclipped the electrical doo hickey. I re-clipped the electrical do hickey of the new ice maker, hung the ice maker on the bolts and then re-tightened them. However,still no ice,my problem was the water valve on the back of the fridge behind the cardboard. Although it was still giving H2O thru the door it was not allowing water to flow to the ice maker. I reccommend pouring some water into the ice tray of the ice maker. If it makes ice and dumps it in to the holder, your ice maker is OK. If it turns out to be your water valve, that fix is easy as well. I HIGHLY reccommend watching the "fix it" video associated with that part. That repair also took less than 15 minutes. Good Luck! KC Bridgewater,NJ

R&R DOOR SEAL VERY EASY TO INSTALL THANKS TO ALL

I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.

It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.

We found the model number and looked online and found this site. The diagrams they provided was very helpful in finding the bin we needed. When the bin arrived it was exactly what we needed. Thank you for your excellent service.

i am done with handle put it easy job

Did nothing. The old bin had been repaired so many times just trying to make it stay in place that we threw the old one away and bought a new one. While at it, I looked to see if I had room for another shelf bin. I simply snapped it on too. The new door bin that I purchased does not stay on any better than the one I replaced. My summation would be that the little clips that protrude to hold it on are either too rounded and it slips off or they are simply not long enough. One bump and this bin is in the floor along with it's contents.

I can't believe I put if off so long... so easy to do and PartSelect was very fast, efficient, and the cheapest vendor for my part.

First I watched the video that provided - extremely helpful - thank you- when the part arrived I removed the drawer and shelf - unscrewed the screw- pushed the slide catches to one side and removed - then I screwed new slide on - pushed to lock in the catches and DONE! That simple - EASY PEESEY!! THANKS SO MUCH FOR VIDEO AND SUPER FAST NEXT DAY SERVICE - AMAZING HOW FAST!! WILL USE ANYTIME I NEED PART AND HIGHLY RECOMMEND YOUR SITE! TIME- 5 MINUTES TOPS!

Order parts on sat.afternoon,and got part on Tues.aand installed in less them 2 min.

Removed power , unplugged wires and 2 screws then reversed the process 1 hour later first batch of cubes dropped into bin

The knob came in the plastic package. It was the correct part. I opened the package and placed the knob on the prongs. Now it works fine.

Thanks
John S.

After disassembling, the thermal fuse I ordered were not and exact fit, I had to cut off the ring terminals, strip the insulation back and splice it in.
It works.

Snapped it in shelf in designated slots

Thawed out freezer, I recommend laying a couple old towels in freezer to soak up melted ice. Replaced old thermostat with new part. Removed 2 screws, removed back plate, unplugged 2 connectors and cut 2 wires. Crimped in new thermostat and repositioned to original part location. Reconnected plugs as I reinstalled back plate. Installed 2 screws and connected power. Works like new! Trouble shooting and part installation video is very helpful, great site!