FRS23W3AW0 Frigidaire Refrigerator - Instructions

it was really easy changing the ice maker. the only trouble i had was the wiring. it was very stiff and hard to route. it did not work at first but that was my fault did not have the connector plugged in all the way.since then it works great.

I worked for GM as a Frigidaire Tech, before starting my own business. I have retired now.
I took the three screws off the back of the bracket holding the motor. Disconected wire harness and pulled out the motor. Reverse to install. servantoftheking@hughes.net

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Looked at video on how to remove and reinstall support and followed the instruct ions

Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.

None of this was obvious - an online tip from another member was invaluable.

Remove shelves and rear panels to get to motor. Motor is held in place on shroud by simple strap. Remove fan blade, then un hook strap, remove and save rubber spacers on old motor to reuse to remount new motor. New motor Mew motor has wiring harness that is universal. Cut out the three wires that go to the new motor leaving long as possible, cut wires from old motor as long as possible, strip ends of all wires 1/2 inch, connect wires by color,slip into provided wire connectors and crimp. Pull on wires to insure connection. Tie wires together so they don't touch the coils. Plug in and check operation. If all is working unplug and replace all covers and shelves. Plug back in and it will take few hours to reach operating temperature. Video of side by side repair shows easy removal of panels and motor.

The repair was easy. It just required a little time and patience. There are about a half dozen screws to remove and three of them are very small. I woild suggest a phillips head screwdriver with a magnetic tip for the small screws. They can easly fall into the control unit and be hidden. If they happen to fall, a small pen-type magnet that is expandable will make it easy to retrieve. I used a small set of needle-nose pliers to replace the small metal plates over the plastic pins that hold the water actuator in place. If your are careful, this repair can be done without disconnecting any of the electrical wiring.

It was very simple-it is just an insert glass shelf above the vegetable drawers. But, it was fairly easy to identify on your website and delivered in about two days.

Turn off ice maker
Slide wire harness shield off connector
Disconnected harness
Loosened 2 wall screws
Remove old ice maker
Installed new one reversing process

I removed the two screws and unplugged it. I then attached the pigtail to the appliance, then to the fridge. I had to push the excess wire harness into the hole in the back. It took a few minutes to move the rest of the harness out of the way by curving it upward and securing it with a nylon tie.I ordered the ice maker from Part Select on Sunday night and it arrived at 8:32 Tuesday morning, THANK YOU! I ordered very simple weed cutter parts from Sears a week ago and they haven't even shipped yet!

I removed the old ice maker and unplugged the cable. Screwed in the new one with a 1/4 nut driver at the 2 mounting screws, plugged cable in. Checked ice maker with a small level before final. All Ok and after night I had Ice and it has been working great since.

From discussions with friends, I determined the problem might be easy to fix. The fridge made a lot of noise, but the compressor DID come on, and inside the freezer was cold, but the main fridge was warming.

After unplugging the fridge, I removed the fan assembly in the freezer (there were about 4 nuts and a couple of plugs to uncouple.

I could see right away the fan blades has broken off, but the motor looked good. The new new fan pushed easily onto the shift and fit perfectly in the housing.

I reinstalled the fan assembly, plugged in the fridge, and right away heard the new fan come on - very quietly. What was a roar became a whisper and the fridge was down to 38 degrees with a few hours.

Emptied the shelves off door and pulled door off fridge swet on counter and took out old plug and put new one on.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wiring harness plug, replaced the old timer with the new one, re-connected the wiring harness and reinstalled the mount in position. Hardest thing about it was lying on the floor.

It was a dreary day, too cold to be outside so I decided to tackle this repair. The first problem was one of the three screws holding the dispenser to the door was rusted in and would not come out. If I was smart I would have stopped there, but in the spirit of Tim the Toolman I found a way to work around it. I was able to get the panel off and disconnect the plug in wires and twist it to the side. The actual change of the paddle was a breeze- three screws and it was done. I turned the front section back into place, connected the wires and proceeded to replace the two remaining screws. All of a sudden the ice diispenser kicked in! First in the crushed mode then in the cube mode. You would be amazed how much ice the dispenser actually holds! I was trying to take screws out to disconnect the wires and catch ice at the same time not; an easy task. Once I had all the ice picked up I tried again and all seemed fine-the chilled water even dispensed again. Problem solved? Only until there was ice in the dispenser again and it decided to start dispensing on its own again. This time I learned and unplugged the appliance from the wall. I took everything apart again and disconnected the wires from the control panel and reassembled without reconnecting it. The repair company will be coming out next week to fix. Hopefully what would have been an easy fix will not become an expensive repair. It was one of those times I should have followed my gut when I ran into the first obstacle. I'll let you know the outcome when the professionals do their work.