FRT21PRGW3 Frigidaire Refrigerator - Instructions

I used a flat head screwdriver to pry open the front of the socket as I pushed the socket toward the freezer side. I unplugged the two wires connected to the socket then re-connected the two wires to the new socket and popped the new socket back in. I then put a new light bulb in and we had light again in the fridge.

Snapped in missing brackets, cut bar to fit and installed.

I watch the how to repair video on line and the repair went very quick and easy.It was just like the video,no hidden suprises.

Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.

Just took it out of the box, wash it and put it on the inside door.

Called Parts-select they helped me out because I had different part number they guided me to the correct part and sent it in no time the part arrived and within 3minutes the part was on and looking good.

Dear Part-select,
I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 part if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work


Tom Houck
Spokane, WA
Houck Photo
509-723-3418
[email protected]

Problems. Two screws holding temperature control module to the plastic case did not fit the holes in temperature controler were too big. So I used gorilla glue to help secure but it was still loose a little bit with all the connections made i turned it on but it did not work

After realizing the engineering on this dryer was different, I was able to access the temperature control thermostat through the front, along the side of the heating element. Several philips screws hold the front on, removing them allows you to take front panel off. At that point the heating element is below. I took a picture of the wires, so that when I started removing them, it would be easy to reconnect. Two screws hold the heating element in place, upon removing the heating element housing pulls gently forward and out, be careful of the wires, the thermostat is the second thing connected to the housing of the heating element. Two more philips screws hold the housing to the bottom of the dryer. Two wires are removed from thermostat, which is also held in place by two philips screws. Remove wires, one at a time and place on thermostat exactly as they were on old thermostat. Hold new thermostat in place with the two Philip screws, and reassemble in reverse order. And enjoy your working dryer once more, hopefully for years to come.

Snapped the end caps onto the existing shelf, and eased the assembly into the door slots. Light tapping with a hammer was required to fully seat the assembly into the door. All in all, a straightforward and simple repair.

Put glass in the new crisper cover and the support bar in place.

I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.

Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.

Removed the old support bar which was broken, stuck the new one in, and adjusted the height. Fit perfectly.
The crisper draw cover supports were stuck in the frame. I used a screw driver to pry them loose. The new ones fit in perfectly, and voila - a perfect fit.
Refrigerator door shelf bin snapped into place with no problem.
Very satisfied with the time to receive parts, time to do repair, and final outcome. Would definitely order from you again.

The process of repairing the draw was very simply. First I removed the broken part with a screw driver and simply slide the new part on and secured the part w/ a screw and that was it.