MRS20HNGW2 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- EDWIN from ELWOOD, IN
- Parts Used:
- 5308000010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
loud noise fan blade broke,off balance
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Weems, VA
- Parts Used:
- 215267701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wrong size listed on website.
The end cap is easy to remove and replace. The personnel at PartSelect was extremely helpful in re-ordering the correct part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from Gulf Breeze, FL
- Parts Used:
- 215473602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
sheft ends brolen
Cleaned and removed old ends, applied new ends and installed. Ends fit to order, shipping quick and parts affordable. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Piscataway, NJ
- Parts Used:
- 215267701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door end cap broken,
Put the new ordered door end caps in place, everything worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Orange Park, FL
- Parts Used:
- 215473602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
clips on both end caps we broken and the crossbar kept falling off.
First i pulled the crossbar off the door, then I pulled both end caps off the crossbar and then I
put the two new end cap on the crossbar and then tapped snoggly into place with the palm of my hand. Job done. took all of about 5 seconds.
put the two new end cap on the crossbar and then tapped snoggly into place with the palm of my hand. Job done. took all of about 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from Coralville, IA
- Parts Used:
- 215473602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door end caps were broken and not fixable
I simply placed the retention bar between the new end caps and popped it into place. Took about 10 seconds to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from Kirkland, WA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
freezer worked frig was warm. Ice maker is still not working
Removed two screws to get to defrost time pull panel down remove two screws holding time and reinstall
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Defiance, OH
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
leaking water down into fridge
just like the video showed...it was excellent!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Fort Sill, OK
- Parts Used:
- 215473602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
We Are Moving Out Of Military Housing And We Had To Replace The Freezer Door Holder Before We Moved Or We Would Have Had To Pay For The Wholr Refrigerator
We replace the end pieces to hook the holder back on the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Stuart, FL
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
coil Iceing up
took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Memphis, TN
- Parts Used:
- 5303917954, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
refrigerator was not cooling
Ordered new parts, removed old parts, put in new parts. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Exton, PA
- Parts Used:
- 5303917954, 215846602
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Freezer icing up
Part Select suggested probable causes and supplied videos of how to make the repair of a 25 yr.old refrigerator along with the specific parts to order. I was about to trash the old refrigerator but after replacing the parts for a total of about $40 and 1 hour of time it works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from merrillville, IN
- Parts Used:
- 215846602
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Heater not coming on - coil frosting up- freezer and Refrig. warm
The instructions given to me by part Select were very good.I replaced the Timer- checked the heater with oham meter it was good- checked the door weather striping it was good and replaced the thermostat with new .So at this point I may need to call a professional unless some one has another solution.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne T from Galway, NY
- Parts Used:
- 5303917954
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Freezer was not defrosting thus refrigerator was not cooling
1. Unplug the refrigerator.2. Remove the storage rack and back panel in the freezer. 3. Locate the thermostat. 4. Defrost the freezer coils , i used a hair dryer. 5. Remove the thermostat from the cooling coil and then clip the connecting wires close to the unit. 6. Strip the ends of these wires and connect these wires to the wires of the replacement unit using the supplied wire connectors. 6. Heat seal with a lighter the connections using the water shield sleeves provided and further wrap connections with electrical tape. 7. Reconnect the thermostat to the cooling coil at the location it was removed from. 8. Replace the freezer back panel removed earlierand the storage rack if you have one. 9. Plug the freezer back in. My refrigerator has been working ever since the repair. There are several YouTube videos available that walk you through the diagnoses and repair process. They are very good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Owatonna, MN
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
It would freeze up or not cool at all, depended where the clock stopped.
Removed the lower trim panel from front of fridg. and loosened two screws enough to turn it about 1/4 inch so the screw heads were in the larger holes. Pulled it out disconnected the wire connector and transfered the heat shield and screws to the new clock, connected the wire connector and aligned the screws. tightened them and job done. Has worked like new sense. Thanks Roger
Was this instruction helpful to you?
Thank you for voting!