MRT13CREW2 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- George from Eatonville, WA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Defroster didn't work
Ordered a new defroster timer and replace old one. It works just fine. A $35 repair vs a $500 new appliance.
Cool.
GWE
Cool.
GWE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Connie from Seneca, SC
- Parts Used:
- 5303324302, 3206150
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
end cap broke
First I removed the broken end caps. I placed the new end cap onto the shelf bar and snapped the end cap into the holding slot on the door interior. Took about 5 minutes. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from Pima, AZ
- Parts Used:
- 5303917954
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Refrigerator keeps frosting up and not cooling
Refrigerator started frosting up and running all the time.I'd defrost it and it would frost up again in about a week.The timer seems to be work so I just guest it mite be the Defrost Thermostat.I removed the duck in the center and back panel in the freezer compartment defrosted it and switched Thermostats and replaced panel and duck, going to lower compartment of the refrigerator.So far it seems to be working a little more time while tell.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Newton, KS
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Refer iced up and would not keep the bottom cool. It was 70 Farenheit inside.
I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sadrudin from SAN DIEGO, CA
- Parts Used:
- 218396700
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
The hole on the handle mounting block was too low
I had to loosen the screw holding the mounting block and increase the hole size to fit the screw on refrigerator
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Hudson, WI
- Parts Used:
- 5303324302, 3206150, 215366002
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
The door shelf retainer bar was too long, 6" to 8"
I measured the width I needed and used a handsaw to cut it the proper length. Then I snaped the pieces in and it was a perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Sierra Madre, CA
- Parts Used:
- 5303917954, 215846602
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Coils kept icing and refrigerator stopped cooling lower compartment.
Replaced defrost timer & thermostat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amit from Glendale, CA
- Parts Used:
- 218428101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Handle borke into 2 piece
As I was aware hot install it, bec a couple of days back, the handle pop out of the lower screw shaft. The easy steps is put the lower part first, keep the handle diagonal to the door, once the lower screw is fit into the shaft, turn it to right to place the holes on the door holes and just jack in the screw.
Its pretty easy.
Its pretty easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LUIS from CENTENNIAL, CO
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer built ice, fridge not cold enough and running constantly.
Removed front low grill, removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. Reversed process to install new timer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from Kirkland, WA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
freezer worked frig was warm. Ice maker is still not working
Removed two screws to get to defrost time pull panel down remove two screws holding time and reinstall
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWIN from ELWOOD, IN
- Parts Used:
- 5308000010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
loud noise fan blade broke,off balance
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Verona, PA
- Parts Used:
- 5303324302, 3206150
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
both end caps broke
Door panel was already off. Took off broken caps, placed new ones on & put back on door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from STATEN ISLAND, NY
- Parts Used:
- 5303324302, 3206150
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken End Caps On Center Door Shelf
I removed the broken end caps by hand. They snap in to the center retainer bar. I ordered replacement parts from part select on their website. New end caps arrived in a couple of days. I installed new caps. No tools needed. Great service by part select. Thank you tm staten island ny
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brad from minneapolis, MN
- Parts Used:
- 5303917954, 215846602
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Freezer okay, but fridge was warm
Website was great!
The defrost timer was right in front. 2 minutes and a screwdriver and I had it replaced.
To replace the thermostat, I had to take out the back panel, defrost it and then install the new part. the only problem was that the heatshrink tubing they sent was too large. Otherwise, it worked great.
The defrost timer was right in front. 2 minutes and a screwdriver and I had it replaced.
To replace the thermostat, I had to take out the back panel, defrost it and then install the new part. the only problem was that the heatshrink tubing they sent was too large. Otherwise, it worked great.
Was this instruction helpful to you?
Thank you for voting!