WRS24WRBD1 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- lynne from huntington, NY
- Parts Used:
- 215162502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken rail
Removed basket to access rail...used nut driver to remove screws from exisiting rail (BE SURE TO SAVE!!!!) Lined up new rail and replaced screws.......replaced basket....SUPER SIMPLE!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chester from Oak Lawn, IL
- Parts Used:
- 215501901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fan not running.
removed old fan and replaced it.3 screws and plug.Always unplug appliance when working on it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Buffalo, NY
- Parts Used:
- 5303289501, 5303289500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Sides of drawers were cracked, unable to use.
I found PartsSelect on the web, input my appliance model# and type and a very easy to read diagram of my appliance appeared. I simply selected the parts I needed from the diagram,and the part numbers were displayed. I placed my order and 2 days later the parts arrived, and I installed them immediately. No fuss, no problem. Great Service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from GIBSON CITY, IL
- Parts Used:
- 5303289501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Drawer was broken.
We moved the refrigerator out so the drawer could be removed. (It was close to the wall) After removing the drawer the front of it had to be removed, then put on to the new drawer. The hardest part was that replacement because we had trouble getting it lifted up. Then the drawer was put in, refilled, and refrigerator moved back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derekandkelsey from WINCHESTER, VA
- Parts Used:
- 3206319
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Blown thermal fuse for Ice Maker
After disassembling, the thermal fuse I ordered were not and exact fit, I had to cut off the ring terminals, strip the insulation back and splice it in.
It works.
It works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chester from STOCKTON, CA
- Parts Used:
- 5303288973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
4 broken drawer cover supports
Followed someone before me instructions. very simple and easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KATHY from MURFREESBORO, TN
- Parts Used:
- 5303918277
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
ice maker quit working/and it was leaking
BOUGHT NEW ICEMAKER TOOK TWO SCREWS OUT, UNPLUGGED THE ELECTRICAL CONNECTION. REMOVED OLD ICEMAKER, PUT TWO SCREWS BACK INTO REFRIGERATOR(DON'T SCREW ALL THE WAY IN AS THE NEW ICE MAKER WILL FIT ON. HOOK ELECTRICAL CONNECTION AND ADAPTER (THAT COMES WITH IT). PUT THE DRAIN TUBE IN ITS SPOT, HOOK ICE MAKER ONTO THE TWO SCREWS TIGHTEN EM DOWN. I DID THIS RIGHT BEFORE I WENT TO A BIRTHDAY DINNER WITH MY HUSBAND, WAS ALREADY DRESSED AND READY TO GO AND I TOLD HIM ILL PUT IT IN SO WE CAN HAVE ICE WHEN WE RETURN. ENDED UP BEING A SURPRISE PARTY FOR ME AND WHEN WE RETURNED WE HAD ICE. IT WAS SO EASY EVEN A GIRL CAN DO IT!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from GLENDORA, CA
- Parts Used:
- 5303917954
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
freezer colk, refrig warm
Followed the instructions provided in your video, took less than 15 minutes and works like new. Thank you for the parts and the advice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dwayne from lincoln, NE
- Parts Used:
- 218215241
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
door closer spring had broken
A pretty easy, remove and replace, project. The spring that closes the fridge door had broken. Just pulled out the old part on top of the appliance and put in the new part. I noticed that part of the problem was that the bottem hinge needed a little lubrication too, as the door wasn't closing as easy as it should with the new part installed. I can't complain though, the side by side fridgeadaire is getting old and this was a very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carol from woodland, WA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the freezer would stick in defrost and not come out
Removed the vent cover at the bottom. Removed the screws. disconected the harnes and put the new timer in. This was a very easy fix. Thank You!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colline from PENDLETON, OR
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker not making Ice
Unscrewed (loosen) screws lifted unit out unplugged electrical connection. plugged in unit hung on screws tightened screws and had ice in less then 1 hour. Rick
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Seal Beach, CA
- Parts Used:
- 215267701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
end piece broken that held bar on freezer door shelf
attached the bar to the end piece and slipped it into the proper opening. Easy I ordered the piece one morning and received it the next morning. Great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- colleen from salt lake city, UT
- Parts Used:
- 5303918277
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench (Adjustable)
ice machine was now working correctly
watched the video (VERY helpful) and then removed the old icemaker and replaced it with the new one. Difficult only because of the small working space in the side by side freezer plus you can't see what you're doing when you tighten the screws. Working like a charm now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Pinole, CA
- Parts Used:
- 215846602
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Frost in freezer, fridge not cold
From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Lake Luzerne, NY
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
first fresh food too hot, then freezer too hot
Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done!!! Couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!