GLHS68EEPW4 Frigidaire Refrigerator - Instructions

I replaced the water valve, but it still did not fix the problem.The old water valve I took out I'm assuming worked fine, I think the real problem is ice building up in pipe or some other blockage.

Parts select was very fast in shipping, very positive experience with them.
I will definitely purchase again from this site.

I followed step by step instruction in the hinge kit; Replacing the old hinge with a new hinge and two new plastic cams in the kit. The kit hinge has an adjustment to level the right door with the left door. Everything is done in 20 minutes for a senior guy like me. Very easy.

removed rear cover, removed screws, diconnected water line connections, cut off old water line connection, installed new compression water line connection, replace screws in water line housing, replace rear cover.

worked fine

very easy to install...shipping was really fast...i would order to this website again....

Installation was completed by following the online Parts diagram. Had to completely remove all parts, including the blades in ice crusher, and re-assemble. Glad the online diagram was clear and easy to read.

Removed the ice maker. Took off the cover and proceed to remove the motor. The only trick was to dis-assemble the electrical connector to replace the wires. I chose to do this rather than splice the new motor into the existing system and it was simple with a little patience.

Easiest repair to make and half / third the money for a new ice maker. The in-laws have ice again (it was over a year).

The replacement glass was a perfect match !!! So pleased...
I was very surprised on how quickly I received my part. I
would definitely recommend your Company to my family and friends. Thank you

The parts supplied were made to fit. The hardest part was getting the original broken tabs out of the internal walls of the fridge with out damaging the internal insulation. I punched the center locking pin through completely, dug out the broken tabs and then reached into the hole with a dental pick and pulled out the center pin. The new parts fit perfectly and with a plastic mallet, tapped the new locking pin into place.

Pulling the old seal was the easy part. The problem became dificult when I opened the seal package. Either Part Select or UPS had folded the seal in half. Witch caused the wire inside the seal to become crimped up. I used a pair of pliers "carefully" to straighten the wire as best I could. Luckly it worked, after pressing it firmly all the way aroud about 5 or 6 times. I'll still keep an eye on it for the next couple of weeks.

loosen 2 screws
unplug connector
remove
replug
replace
tighten 2 screws
done

Ordered a new shelf which arrived very fast. Installed in no time at all as it just slides in and rests on brackets. No tools needed and the new part looks just like the original.

The old support just unscrewed & then the new one screwed right on with two screws.

I just took the old filter off and replaced with the new one, after I run the water for about 15 minutes and tossed the old ice and cleaned the tray.

I had removed the housing that the drum was in and taken the screws out to get to the broken drum. I removed it there was a set of 6 blades that crushed the ice that had to go back on the same order when I removed these I put them on a piece of wire in the order they came off (so I would get them back I the correct order). Then I reversed the order and reassembled it in the opposite direction . It was fairly easy to do. I'm a 68 year old disabled woman so if I could do it I'm sure you could to. Good luck. It cost me $14.00 if I had bought the whole assembly it would have been $150.00. So it was well worth my time and effort.

We followed the video instructions and it went fairly smooth. After turning off the water at the street we found that the faucet at the wall had it's own "on/off" valve. When finished, we turned on the power and heard the gears going through their revolutions, but no ice was made. We waited 24 hours and still no ice. I removed the cover on the ice maker and adjusted the amount of water to see if that was malfunctioning. Still no ice was created. Waited another 24 hours - nothing. Waited another 24 hours (the site said that sometimes the ice maker would take time to reset itself) - nothing. Then on the fourth day after changing out the triple water valve we heard water being dispensed and later that day it put out the first ice in weeks. Another hour later another batch of ice cubes were ready and deposited into the bin. Since that time, we have had a full bin. I moved the set screw back to it's original setting because a little too much water was being delivered. The cubes weren't separating to individual cubes. That cleared up the problem. This was easily completed - we recommend others do their own work. Just be patient for the system to reset itself.