FRS24WSCB5 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Art from Bullard, TX
- Parts Used:
- 5303289501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Poor design resulted in lower crisper drawer breaking on both sides.
Got the new drawer 2 days after I ordered it. Snapped the front off the old drawer and onto the new one, and slid the new drawer in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chester from STOCKTON, CA
- Parts Used:
- 5303288973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
4 broken drawer cover supports
Followed someone before me instructions. very simple and easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from GLENDORA, CA
- Parts Used:
- 5303917954
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
freezer colk, refrig warm
Followed the instructions provided in your video, took less than 15 minutes and works like new. Thank you for the parts and the advice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derekandkelsey from WINCHESTER, VA
- Parts Used:
- 3206319
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Blown thermal fuse for Ice Maker
After disassembling, the thermal fuse I ordered were not and exact fit, I had to cut off the ring terminals, strip the insulation back and splice it in.
It works.
It works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from OSHKOSH, WI
- Parts Used:
- 5303917954
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
freezer was warm
Top freezer took off the panel in freezer and melted the ice around coils and found the defrost thermostat and replaced with the new one. Just followed the instructions from your video on line. Freezer works just fine now. Refrigerator is 38 years old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arand from Yorktown, IN
- Parts Used:
- 5303288973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The original support was broken, tried epoxy and it only held for a few months before breaking again
All I had to do was remove the original support that was on the inside wall of the refrigerator, which I had to use pliers since there were broken pieces, and then I just snapped the new one into the three holes provided for this support. The crisper drawer works fine now. It literally only took about 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colline from PENDLETON, OR
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker not making Ice
Unscrewed (loosen) screws lifted unit out unplugged electrical connection. plugged in unit hung on screws tightened screws and had ice in less then 1 hour. Rick
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Lake Luzerne, NY
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
first fresh food too hot, then freezer too hot
Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done!!! Couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from State College, PA
- Parts Used:
- 5303289501, 218147701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drawer and rails broke due to under design of the components
This was the second time i replaced the drawer and the first time for the frame.The repair was simply removing the old frame from the refrig and removing the rollers from the frame with screw driver. The rollers are reused with the new frame.The frame was reinstalled in the refrig.
The replacement of the drawer requires reusing the drawer front which is easily removable. The only complication with drawer repair was the need to trim some flashing that was not removed after the molding process at the factory to allow the drawer face to fit properly on the new drawer.
this problem is a quality control issue with the manufacture of the storage drawer.
The replacement of the drawer requires reusing the drawer front which is easily removable. The only complication with drawer repair was the need to trim some flashing that was not removed after the molding process at the factory to allow the drawer face to fit properly on the new drawer.
this problem is a quality control issue with the manufacture of the storage drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from West Milford, NJ
- Parts Used:
- 5308013640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
freezer door rack broke
just had to loosen the old, broken piece, and snap in the replacement. Piece of cake
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from WETUMKA, OK
- Parts Used:
- 218147701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
storage drawer frame had cracked in the back
Simple, removed old frame, took off the humidity slide control and installed on new frame. Slid it back in place. Great service, had it the next day, thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from GILBERT, AZ
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
made lots of noise
Loosen two screws, unplug power, lift it off, put new one on and make sure water chute is correct place, tighten screws!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carol from woodland, WA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the freezer would stick in defrost and not come out
Removed the vent cover at the bottom. Removed the screws. disconected the harnes and put the new timer in. This was a very easy fix. Thank You!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from WAPAKONETA, OH
- Parts Used:
- 5303918277
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice maker stopped producing Ice.
After determining the ice maker was getting water but not harvesting the ice, I ordered a replacement Ice Maker. Installation was easy. One electrical connection and two screws. Following the video to make sure I did not miss any steps I had ice in just a few hours. Just in time for a July heat wave!
Was this instruction helpful to you?
Thank you for voting!
Replace the storage drawer supports and Tank Support Stud
Used pliers to remove and install tank support studs.
Was this instruction helpful to you?
Thank you for voting!