FRS20QRCD5 Frigidaire Refrigerator - Instructions

Twisted replacement bulb into place easily. Let there be light!

I removed the front cover from the original drawer and slid it onto the new one from PartSelect. Perfect fit. I recieved my part in only two days with regular ground shipping and I am completely satisfied with the part and service.

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

After posting the specific symptoms and getting feedback, I had narrowed the cause to two linked parts. I ordered both intending to replace first one, then the other as needed. With parts in hand, I pulled off the freezer control knob, used a nut driver to remove the two panel securing screws (behind the face, against the inner ceiling) and gently dropped the cover down. The control (temp sensor and cold control) is easily accessible as it sits wedged into two slots in the plastic cover. The control must be slightly lifted in order to extract the long sensor that attaches to the control and runs under it and into a plastic sleeve behind the panel (the new control comes with the sensor wrapped in a tight coil and it must be unwound for the install). Removed the three wires noting which color goes where. Used needle-nose pliers to remove the small push-on tabs and removed the control. After starting the new sensor probe into the sleeve re-attached the 3 wires to the new control. Used the original as a model for how to pre-bend the probe for the first 2 inches as it was mildly frustrating to position the unit back correctly. Pushed everything back into place, re-installed the screws and plugged the fridge back in...(you DID unplug it first, right?). Still haven't used the second part (defrost timer), but I expect it to go soon...it is a 17 year old refrigerator, after all.

Had to pry off front glass of drawer with screwdriver.Very east install. The shipping for this part was the fastest I have ever recieved.I called at about 2:00pm and had the part the next day at 2:00pm..incredible service

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wiring harness plug, replaced the old timer with the new one, re-connected the wiring harness and reinstalled the mount in position. Hardest thing about it was lying on the floor.

After ordering part on friday morning, saturday evening I was installing new handle on. 4 screws, install trim, trim slides over handle and fastens in.

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

Remove the cardboard access cover at the bottom back of the fridge. On the left side, locate the run capacitor. Remove it by prying it loose from its socket, after first removing the wire hold down clamp. One wonders why the clamp is there, which makes it difficult to get the run capacitor out. Be careful not to disrupt in any way the copper refrigerant tubes. If you mess them up, you will have wasted your time and effort trying to repair the machine. I was lucky, since a failed run capacitor is the problem only about 12% of the time, based on what I’ve read. Hallelujah! It was the problem with my fridge.

From discussions with friends, I determined the problem might be easy to fix. The fridge made a lot of noise, but the compressor DID come on, and inside the freezer was cold, but the main fridge was warming.

After unplugging the fridge, I removed the fan assembly in the freezer (there were about 4 nuts and a couple of plugs to uncouple.

I could see right away the fan blades has broken off, but the motor looked good. The new new fan pushed easily onto the shift and fit perfectly in the housing.

I reinstalled the fan assembly, plugged in the fridge, and right away heard the new fan come on - very quietly. What was a roar became a whisper and the fridge was down to 38 degrees with a few hours.

Looked up similar problems and found it to be the defrost timer. All I had to do was remove the plastic portion in the fridge section to get to the old timer. Popped the new one in and put it back together. Works great now. Would have been almost $150 to have a repair company come out and fix it.

It was a snap. Literally. all I had to do was snap and slide the front off the broken drawer and slide and snap it onto the new.

I removed the housing at the top of the refrigerator compartment that contained the reefer light and temperature adjustment knob. This required a small nut-driver. Inside, I found the old defrost control, unplugged it, unscrewed it with a Phillips screwdriver, and replaced it with the replacement part. Then I replaced the housing to its original position.

First I removed the plastic grill (pulled out, no screws) from bottom of refrigerator, then I removed electrical plug & two screws from old timer (timer located on the front inside left lower side of refrigerator). Installed in reverse order.

Removed the housing with the light, 4 hexhead screws. This exposed the defrost timer, removed 2 hexhead screws, electrical connector and reassembled the unit.

Great resource and service, thank you.