MRT13BSCW5 Frigidaire Refrigerator - Instructions

I used a flat head screwdriver to pry open the front of the socket as I pushed the socket toward the freezer side. I unplugged the two wires connected to the socket then re-connected the two wires to the new socket and popped the new socket back in. I then put a new light bulb in and we had light again in the fridge.

Pulled the few end caps off the retainer bars, pushed the new ones in, and used a medium hand strike to seat the end caps in the doors slots.

the repair went fast and easy. my boyfried measured the retainer bar, cut it with the hack saw installed the right and left side door shelf end cap and inserted the door shelf retain bar. the door looks great. would highly recommend your website and customer service. thanks again.

I replaced the shelf end caps in the shelves of my fridge and I also replaced the gasket around the door.

Every time I would open the door, things would fall out because the shelves were giving, because the end caps were broken. Once I got the new ones, I was amazed that these parts are still available and that they lock right in with no problem. Once you get one in, you then have to place one end of that retaining bar into that, very tightly, making sure the end is completely secure in the cap. Then you can lock the other cap to the other end, lock it into place in the door and whala! It is just that simple.


Now the gaket is another story, it is best to soak the gasket in hot water first to draw it up abit so it will be snug and also to use lubricant such as petroleum around the inside where it is going to fit to the door. This made it extremely easy to afix to my door with no problems. I am so glad for this site.. hundreds of dollars saved!!

After realizing the engineering on this dryer was different, I was able to access the temperature control thermostat through the front, along the side of the heating element. Several philips screws hold the front on, removing them allows you to take front panel off. At that point the heating element is below. I took a picture of the wires, so that when I started removing them, it would be easy to reconnect. Two screws hold the heating element in place, upon removing the heating element housing pulls gently forward and out, be careful of the wires, the thermostat is the second thing connected to the housing of the heating element. Two more philips screws hold the housing to the bottom of the dryer. Two wires are removed from thermostat, which is also held in place by two philips screws. Remove wires, one at a time and place on thermostat exactly as they were on old thermostat. Hold new thermostat in place with the two Philip screws, and reassemble in reverse order. And enjoy your working dryer once more, hopefully for years to come.

Needed to saw the pieces. PUrchased hacksaw.
Son sawed the pieces. Went in like a piece of cake.

unplug power from ref removed old light socket only difference wired a little different checked new socket compaired to old checked terminal ends small big looked at wires big,little plugged up put in new light blub plugged ref power back on work power off pushed socket bac in power on works

A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.

The replacement part was a bit too long (about 6"). Measured length of the existing bar that was on lower shelf and used a rotary tool with a metal cutting disc to make the same length. Everything snapped into place easily.

freezer section remove ice trays ,shelves,unplug ice tray.use 1/4 nut driver remove back panel,use hair dryer thaw ice from evap coil ,unplug tstat remove install new one.plug in ice maker,put back panel back on ,ice maker and shelves plug refridgerator back in

Problems. Two screws holding temperature control module to the plastic case did not fit the holes in temperature controler were too big. So I used gorilla glue to help secure but it was still loose a little bit with all the connections made i turned it on but it did not work

Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.

I measured the width I needed and used a handsaw to cut it the proper length. Then I snaped the pieces in and it was a perfect fit.

I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.

We have a wonderful Kelvinator refrigerator. It has served us tirelessly for more than 15 years - and looks as good as new! (We frequently clean it out and clean the interior and exterior, to keep it looking and smelling clean)

Replacement of the end caps and shelf was very easy!

The broken end caps were removed (missing for years), and it became one of those small projects that one never gets around to. I finally took down the model number and looked online for it. Google or Yahoo (can't remember which) pointed us to you site. I was SHOCKED to see that the parts were still available! I called your friendly customer order line and had a very pleasant experience placing the order. The BIGGEST shock came when the parts arrived THE NEXT DAY!! Just in time for Thanksgiving! You are AWESOME!

The Repair:

Easy as pie. The end caps simply snap into place. I did the left side first, then carefully inserted the metal bar, which is supported by the two end caps. Next I snapped in the right side cap - DONE. It took longer to clean the bar up, than it did to replace the caps!

The Results:

The bottom door shelf is now useable again. We can place 2 liter beverages and juice containers on the door, where they belong! My wife cheered and commented, "The refrigerator is no longer an eye sore when I open it!" :-)

Thank you Parts Select!!!!