RS229GCH1 Frigidaire Refrigerator - Instructions

1. Unplug the refrigerator.2. Remove the storage rack and back panel in the freezer. 3. Locate the thermostat. 4. Defrost the freezer coils , i used a hair dryer. 5. Remove the thermostat from the cooling coil and then clip the connecting wires close to the unit. 6. Strip the ends of these wires and connect these wires to the wires of the replacement unit using the supplied wire connectors. 6. Heat seal with a lighter the connections using the water shield sleeves provided and further wrap connections with electrical tape. 7. Reconnect the thermostat to the cooling coil at the location it was removed from. 8. Replace the freezer back panel removed earlierand the storage rack if you have one. 9. Plug the freezer back in. My refrigerator has been working ever since the repair. There are several YouTube videos available that walk you through the diagnoses and repair process. They are very good.

with patience

All I had to do was change out motors, and the fam would spin right,and the freezer was alive again. With your older models you may have to re-mount the motor bracket in the back for the fan to clear,due to the fact that the motor sits alittle lower than the old model

Replace evap fan motor. Take a close-up picture of the evaporator fan motor installation prior to removing. Take pictures as removing various components.

I followed the advice of many people with the same problem, and replaced the Defrost Thermostat and Defrost Timer. Both repairs were relatively easy, and the problem appears to be solved. The replacement of the Defrost Timer is very easy (about 30 minutes), and I wish I had stopped at that step and waited 48 hours to see if that fixed the problem. But, I wanted to replace both parts that I had purchased - - In my refrigerator, access to the Defrost Thermostat is through the back of the freezer panel. Not too difficult to get to the area, but I had a bit of a problem in replacing the part, and might have been better-off to see if step 1 fixed the issue. The problem that I ran into is that I don't have a crimping tool, and crushed both of the connecting sleeves when trying to 'crimp' them with a set of wire-strippers. Rather than to invest in a crimping tool, I connected the wires and sealed with electrical tape - - Now that the issue is resolved, I will likely re-open and use a proper connecting sleeve (with a proper crimping tool). My advice is to buy both parts, and replace just the Defrost Timer first. Chances are good that it may fix your problem, and you are only out $20 for the second part, which you can leave in your junk drawer until you may need it some day! All in all, it was a great way to spend $40 and avoid a costly service call!

Removed the old burned out evaporator fan, and with the model# was able to find a replacement at PartSelect. I was really surprised that you had the exact part on a fridge that old. Installed the new fan, and the fridge is working beautifully. Thanks to PartSelect I was able to save several hundred dollars.

This is a top and bottom frige. I unplugged the fridge and I took off the sheld in the freezer and removed the blower fan cover and unplugged the fan to remove the back freezer panel. Be careful when moving the fan. It looks sensitive. I used a hair dryer to melt the frost to get to the screws. Because it was frosted the back panel was hard to take off. Don't force it too much, just keep melting the ice. Once it was off the radiator looking thing was completely frosted and iced over and I couldnt even see the thermostat. I started blowing it with the hair dryer and it started melting. It took an hour to get the ice melted enough to actually see and remove the thermostat. You may want to leave the fridge off for a day. I didnt have a choice because I didnt have anywhere else to place the food. I was using the freezer as the fridge. Thats how cool the freezer was. I cut the wires for the thermostat. Im sure you could check which is positive and which is negative. I just looked at the direction the wires went. This works but it is not guaranteed. Check for ground. Google it if you need to know how. I used the clamp connector things but I didnt have a clamper so I used a plier. It works but I didnt like how it clamped. The little tubing didnt work for me becuase I didnt have a solder gun to warm it up and using a match is not good. You'll burn the wire. Buy electric tape and wrap it around. Dont use regular tape. Go to home depot it costs 99 cents. Make sure all ice is melted. Go over everything with the hairdryer to melt the ice. You dont want it to start freezing and clog up the vents, expsecially the one that goes from the fan to the fridge. Before I put everything back together I changed the defrost timer because I figured its best to change it since you never know. I loosened the two screws but first I took offf the screw holding the timer panel. I changed the defrost timer and connected it back. Then I screwed everything together. Then I screwed in the back freezer panel but not the fan cover so I could see if the fan is working. I plugged in the fridge and the fan didnt work. If you look under the defrost timer panel, the timer has a round part that you can move with a flathead screwdriver. Move it lightly clockwise and the fan will start. I read that the fan goes for 8 hours and then it turns off for a half hour. Seems like a lot of time to be on but its been a week and the fridge and freezer are working real good. This website is good and the aprts are cheaper than Sears.

Followed instruction vedeo from partselect. THANKS!!!!!

unplugged frig,removed bottom front cover and loosend 2 screws at bottom front left and slid defrost timer out from behind metal panel,unplugged the old and plugged in the new.frig works great.

Problem not consistent. OK for 2-3 weeks, then freeze coils. Mark and observe the defrost timers manual rotating adjuster. Timer would stop mid cycle. One revolution equals 8 hours of compressor run time followed by 30 minutes of defrost. Replacing timer took 5 minutes.

Based on the diagnosis on this site I thought the 66% odds of the problem being the Defrost Timer looked pretty good, $30 including shipping versus a Sears tech phone estimate of $250-300. BINGO! Just follow the online installation instructions and don't forget to use the reset switch as described. Works like new! THANK YOU

I followed the procedure online and found the thermostat was ok, it had continuity when cold, and the heater coil was also ok, it too had continuity, therefore the problem was a bad defrost timer. the refrigerator works great, thanks parts select!

Unplugged the frig. Removed temp control module from frig, 1 screw with nut driver. Activated defrost timer by rotating adjustment until 2 clicks are heard. Removed two timer mounting screws, unpluged timer, plugged in the new timer, mounted it to the control module with 2 mounting screws. Replaced control module with the 1 mounting screw. Closed door and plugged it up.

pulled down the thermostat cover and unpluged the timer control and replaced it with the new part. total time to repair was about 15 min. there was a vidio on how to replace the new part that just informed me that I did it right!!!!very easy site to find what you are looking for!!!!

replaced the defrosting timer and saved a lot of $ by doing it my self.