FRT21HS6DWB Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lise from CEDAR GROVE, NJ
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven light bulb went dark; it needed replacing
Twisted replacement bulb into place easily. Let there be light!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from parker, CO
- Parts Used:
- 5303918549
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Lightning struct the house and fried the evap thermostat
Noticed the evap fan wasn't working, so trying to disconnect the wire broke the connection so had to order a new motor. Installed the motor but it still didn't work. Had a technician look at it and he said it was the control board. Ordered and installed control board and still didn't work. The only element left is the evap thermostat. Jumped the thermostat and it worked so ordered and installed a thermostat. It works now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Raleigh, NC
- Parts Used:
- 240337901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Shelf door retainer was broken
Our refrigerator door shelf retainer had broken on the side which basically put one shelf out of commission in our fridge. I looked up our fridge on partselect and found the correct retainer and ordered it. The part came very quickly, within just a few days. If fit perfectly and I'm very happy with the part, the speed of delivery, and ease of ordering. I will definitely use partselect again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LYNETTE from AGOURA HILLS, CA
- Parts Used:
- 240350609
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Big oops when I broke the glass shelf while washing in hot water...too hot
I ordered the part, it arrived within 48 hours. I opened the fridge and put the shelf in perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from VIRGINIA BCH, VA
- Parts Used:
- 242201805
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The refrigerator crisper pan cover cracked in the front center.
I removed the glass from the cover, removed the 2 crispier pans and removed and discarded the broken cover. I installed the new cover by making sure the back was flush against the back wall of the refrigerator. After that I replaced the glass and drawers and it was as good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from McLean, VA
- Parts Used:
- 240350609
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken glass insert over refrigerator drawers
I called in because the model # of the refrigerator did not show up on the website. The cust. srvc. rep looked it up and found the part. It was reasonably priced, I received it in a matter of days and it fit perfectly. Thank you! We were preparing to put the condo on the market and broke the shelf while cleaning. It was great to have a resource for a reasonably priced replacement and quick shipment.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANGELA from MEBANE, NC
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator Light bulb went out
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denver from BLAIRSVILLE, GA
- Parts Used:
- 5303918549
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Evaporator fan motor quit and would not circulate cold air from coils.
Remove shelves and rear panels to get to motor. Motor is held in place on shroud by simple strap. Remove fan blade, then un hook strap, remove and save rubber spacers on old motor to reuse to remount new motor. New motor Mew motor has wiring harness that is universal. Cut out the three wires that go to the new motor leaving long as possible, cut wires from old motor as long as possible, strip ends of all wires 1/2 inch, connect wires by color,slip into provided wire connectors and crimp. Pull on wires to insure connection. Tie wires together so they don't touch the coils. Plug in and check operation. If all is working unplug and replace all covers and shelves. Plug back in and it will take few hours to reach operating temperature. Video of side by side repair shows easy removal of panels and motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janean M. from Indianapolis, IN
- Parts Used:
- 240337901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator door shelf retainer
The part was perfect for the door. It snapped into place
on the door.
on the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Otterville, MO
- Parts Used:
- 5303918202, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
freezer frosting over,fridge warm
removed ice maker,,and screws holding back of freezer cover,unplugged wires and removed the cover and fan.wow,only wire to element had come unplugged!went ahead and replaced thermostat,and defrost timer,both were easy to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from AGAWAM, MA
- Parts Used:
- 242193213
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
gasket tearing
grab gasket on a corner and pull...new gasket push raised rib into grove....your Done!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Cedar Park, TX
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
unit quit cooling
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wiring harness plug, replaced the old timer with the new one, re-connected the wiring harness and reinstalled the mount in position. Hardest thing about it was lying on the floor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie L from Eureka, CA
- Parts Used:
- 240338101
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Broken Plastic Edge
Easy peasey just slipped it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gary from ARANSAS PASS, TX
- Parts Used:
- 5308000010
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
I had a broken fan blade due to ice build up from a leaking ice maker.
1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Hawley, PA
- Parts Used:
- 240350609
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Glass Shelf in Refridgerator
I broke the glass shelf in my refrigerator. I had trouble navigating the website, so I called the customer service line, and the lady was lovely to speak with, and ordered my part quickly! In 2 days I had the part, and it fit perfectly!
Great service, great price!
Thank you!
Great service, great price!
Thank you!
Was this instruction helpful to you?
Thank you for voting!