FRS23W3AW9 Frigidaire Refrigerator - Instructions

The repair could not be completed. I ordered a thermostat defrost kit but received a collar arbor for a saw. They do not answer the phone at customer service and the order took close to two weeks to get in the first place. Beware of shopping at this site!

Emptied the shelves off door and pulled door off fridge swet on counter and took out old plug and put new one on.

I removed the two screws and unplugged it. I then attached the pigtail to the appliance, then to the fridge. I had to push the excess wire harness into the hole in the back. It took a few minutes to move the rest of the harness out of the way by curving it upward and securing it with a nylon tie.I ordered the ice maker from Part Select on Sunday night and it arrived at 8:32 Tuesday morning, THANK YOU! I ordered very simple weed cutter parts from Sears a week ago and they haven't even shipped yet!

From discussions with friends, I determined the problem might be easy to fix. The fridge made a lot of noise, but the compressor DID come on, and inside the freezer was cold, but the main fridge was warming.

After unplugging the fridge, I removed the fan assembly in the freezer (there were about 4 nuts and a couple of plugs to uncouple.

I could see right away the fan blades has broken off, but the motor looked good. The new new fan pushed easily onto the shift and fit perfectly in the housing.

I reinstalled the fan assembly, plugged in the fridge, and right away heard the new fan come on - very quietly. What was a roar became a whisper and the fridge was down to 38 degrees with a few hours.

First I removed the clamp, pulled out the part, and diconnected the two wires on the side and a small screw. Reconnected the new part with the small screw, connected the wires and plugged the part back to the side of the motor. Whaa La, Done.

Turn off ice maker
Slide wire harness shield off connector
Disconnected harness
Loosened 2 wall screws
Remove old ice maker
Installed new one reversing process

I removed the old ice maker and unplugged the cable. Screwed in the new one with a 1/4 nut driver at the 2 mounting screws, plugged cable in. Checked ice maker with a small level before final. All Ok and after night I had Ice and it has been working great since.

It was very simple-it is just an insert glass shelf above the vegetable drawers. But, it was fairly easy to identify on your website and delivered in about two days.

I broke off remainder of clip, and used phillip
screwdriver and pushed pin into wall. I lined up new support and pushed in peg to secure

took door off(very easy two bolts on top)lift door replace parts

Removed ice tray, disassembled ice tray assembly and crusher housing making sure to note the spring location, spring etc, installed new plastic housing making sure to reinstall the spring properly and the fixed crusher blade into the notch cutout., reassembled ice tray.

It was a dreary day, too cold to be outside so I decided to tackle this repair. The first problem was one of the three screws holding the dispenser to the door was rusted in and would not come out. If I was smart I would have stopped there, but in the spirit of Tim the Toolman I found a way to work around it. I was able to get the panel off and disconnect the plug in wires and twist it to the side. The actual change of the paddle was a breeze- three screws and it was done. I turned the front section back into place, connected the wires and proceeded to replace the two remaining screws. All of a sudden the ice diispenser kicked in! First in the crushed mode then in the cube mode. You would be amazed how much ice the dispenser actually holds! I was trying to take screws out to disconnect the wires and catch ice at the same time not; an easy task. Once I had all the ice picked up I tried again and all seemed fine-the chilled water even dispensed again. Problem solved? Only until there was ice in the dispenser again and it decided to start dispensing on its own again. This time I learned and unplugged the appliance from the wall. I took everything apart again and disconnected the wires from the control panel and reassembled without reconnecting it. The repair company will be coming out next week to fix. Hopefully what would have been an easy fix will not become an expensive repair. It was one of those times I should have followed my gut when I ran into the first obstacle. I'll let you know the outcome when the professionals do their work.

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

A little difficult getting out due to restricted space, I took off the fan blade, that gave extra working room. Then it went well going back together,and it all worked as advertised. Thanks. p

I used pliers to get the remaining shelf support studs out, then the new ones just snapped right in place. Very easy repair!