FRT21IQRJW0 Frigidaire Refrigerator - Instructions

I used the tool at Partselect that in theory allows diagnostic of the problem to be repaired. The result was that more tan 90% of the time with the introduced symptoms it had to be the thermostat. I order the part, got it quickly and installed. It did not fix the problem. So, be careful with the diagnostic tool, because it is just based on what most people buy when they have a particular problem. Videos for installation are great. If diagnosis was better, this would be fantastic. In my case there might be a different problem.

Loosen two screws, unplug power, lift it off, put new one on and make sure water chute is correct place, tighten screws!

After determining the ice maker was getting water but not harvesting the ice, I ordered a replacement Ice Maker. Installation was easy. One electrical connection and two screws. Following the video to make sure I did not miss any steps I had ice in just a few hours. Just in time for a July heat wave!

Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done!!! Couldn't have been easier.

Removed the back panel in freezer compartment with the nut-driver. Then I cut off old thermostat connections, and spliced in new thermostat connections (repairman had already replaced defrost timer, and said not to trust connectors included on wires-they failed often). Then I snapped thermostat itself onto cooler coil. So far so good, fridge is running at 35-40 degrees a week later. Thanks Parts-Select!!!

I removed the shelf, took off the old ends caps, replaced them with the new ones and put the shelf back in place. No glue or tools needed and the job was completed in under 2 minutes.

First, my husband removed the shelf assembly. Then he unscrewed the boken bracket. He then screwed in the new bracket and proceeded to install thecomplete shelf assembly back into the fridge. Placed the meat drawer back into correct location, to fit back into rail brackets. All done.

Had to remove all screws on rear back cover of freezer inside, unplugged refridgerator, uncliped thermostat, unpluged thermostat. Replaced thermostat with new one in the same location, and let defrost fulley. Reassembled, pluged in, and tested. All was good. But I did also replace timer at first part of the repair so I suggest you replace both at the same time.

Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.

Called Parts-select they helped me out because I had different part number they guided me to the correct part and sent it in no time the part arrived and within 3minutes the part was on and looking good.

I watch the how to repair video on line and the repair went very quick and easy.It was just like the video,no hidden suprises.

The meat drawer is already pulled out because the broken rail could not support it. 1st I removed the shelf. Then I removed the 2 screws connecting the rail to the shelf. I then replaced the rail, screwed it together and put the shelf back in place. I put the meat drawer back on the rails and it's done.

Removed 2 screws that hold ice maker in place. Unplugged and took out of freezer. Used the screws I took out to put new ice maker in. Plugged in the power and in 2 days I had a full ice bin and haven't had any worries since. Should have replaced the broken one along time ago but thought that the process was harder than this. Very easy and suggest this to anyone having ice maker issues. Less than $100 and never have to buy ice for the house again.

I loosened the 2 1/4 inch nuts with a nut driver, disconnected the wire harness, and removed the old unit. to replace, I simply connected the harness and bolted the unit back in. The job took about 10 to 15 minutes and the new unit works better than the old one ever did.

Ordered ice maker, watch video of how to. It takes less than 5 min. Installes just like the video. Loosen 2 1/4" Screws, lift ice maker up, unplug old unit, Reverse. Just make sure water tube is lined up when you install new unit and wire is tucked up out of the way. Mine did not really start making ice till the next day.