FRT21PRCW2 Frigidaire Refrigerator - Instructions

Decided to clean the refrigerator at the same time as replacing the broken part. Took shelf out, removed glass, washed all parts, removed broken rail (two screws) and replaced new part. Piece of cake!

I first thought the defroster heater broke - took the back wall of the freezer off and cooling fins were fine. Then took the defroster timer out and opened it up. The contacts were badly burnt so the compressor and fan ran during only part of the cooling cycle. Replacing the timer took less than 5 minutes - turn off the power, remove one screw to take out the control box, cut the ground wire (new timer housing is plastic and does not have a ground connection), remove two screws to unmount the timer, unplug the old timer, plug in the new timer, fasten with two screws, put the control unit in and fasten with one screw, turn power back on.

real easy with the help of the video , made the difference

You guys at Partselect are the best!!! Went to your site, typed in my appliance symptoms, and received possible fixes. Ordered the suggested parts (under $50) on a Sunday night and got em Tuesday am. Installed the easiest one first and Voila!!!! Frig is working great. Thanks Bob S

Remove 4 screws that hold up overhead controls, this is also the part that holds the light. Unplug the timer and replace. Super simple and runs great now. After you plug it in it may take a few minutes to kick on the compressor but it will. Also I was pleased it was a factory Frigidare part. Price was right.

Problem not consistent. OK for 2-3 weeks, then freeze coils. Mark and observe the defrost timers manual rotating adjuster. Timer would stop mid cycle. One revolution equals 8 hours of compressor run time followed by 30 minutes of defrost. Replacing timer took 5 minutes.

I followed the procedure online and found the thermostat was ok, it had continuity when cold, and the heater coil was also ok, it too had continuity, therefore the problem was a bad defrost timer. the refrigerator works great, thanks parts select!

snaped new caps into openings

Having looked at the broken area, in some frustration, for several years, I had a good idea how it all went together: the front end slips over a metal lip suspended from the front of the shelf above, and the rear is held in place by a single screw (single slot with hex-dead). The most time was taken clearing the items off the shelf above. Having done that, the shelf was easily lifted up and removed. Flip it over to expose the screw at the back. Remove that screw and discard the old/broken hanging rail. Slip the front end of the new rail (carefully) over the metal lip. At the rear, line up the hole on the hanger with the hole in the mounting bracket and re-insert the one screw. Re-install shelf and slide the drawer back into place on the hangers. Good to go.

Diagnosis: used wiring diagram attached to frig and determined cause could be wiring, heater element, thermostat or timer. After completely defrosting the frig (turned it off) I removed the rear cover in the freezer and looked for an obvious problem. None seen. Removed temperature select pod from the frig box and looked for obvious problems. None seen but defrost timer appeared poorly made. Repair: Since I had no practical way of checking the defrost cycle in operation, I checked probable failures on the Part Select website and saw defrost timer as most probable. I ordered the timer. Installed it. Waited a few days to make sure the frig went through a few defrost cycles then removed the freezer rear cover. There was no excessive frost buildup so I'm reasonably sure the repair was successful.

pulled down the thermostat cover and unpluged the timer control and replaced it with the new part. total time to repair was about 15 min. there was a vidio on how to replace the new part that just informed me that I did it right!!!!very easy site to find what you are looking for!!!!

Just slid it into place.

replaced the defrosting timer and saved a lot of $ by doing it my self.

Just followed the online instruction video .It was very easy.

remove two screws with a phillips screw driver and replace part in same fashion. Easy 5 minutes. Part arrived next day with regular mail. Surprised!