FRS20ZGJD1 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gordon from Marlborough, CT
- Parts Used:
- 5303299165
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Odor like burning Electrical all through refrig.
Remove back panel inside Freezer compartment remove 2 screws that hold (small) fan motor. Unplug electric motor supply and install new motor in reverse order
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert H. from Grand Blanc, MI
- Parts Used:
- 297216600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
frezer not staying cold enough to freze newly added product
took the shelves out, unscrewed the rear panel,unpluged the thermistat and uncliped it from the line.Replaced with new thermistat in the reverse order. Before turning the unit back on,allowed the coils to defrost.All of the process was shown in your vidio that I was able to view while ordering the part. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Milton, WV
- Parts Used:
- 241885001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
housing-crusher was broken
removed ice maker box and disassembled crusher unit on front of box and installed new housing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Athens, AL
- Parts Used:
- 241860803
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
ice crusher blades not working
got replacement ice container with ice crusher and dispenser in the door. removed broken one and slid in the new one like a drawer and started crushing ice right away!!
Was this instruction helpful to you?
Thank you for voting!
Rust had corroded Front Plate and Drive Blade
Installation was completed by following the online Parts diagram. Had to completely remove all parts, including the blades in ice crusher, and re-assemble. Glad the online diagram was clear and easy to read.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Niceville, FL
- Parts Used:
- 241734001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
There was a hole in the plastic bin where ice fell through to the freezer.
I removed the screws that held the the ice dispencer from the bin. I than removed three screws from the bottom of the bin. I put the new plastic piece on the end of the spiral piece that
pushes the ice. I inserted the spiral piece back into the hole. I than screwed the ice dispencer
to the bin and re-inserted it back in the refrigerator.
It took me about 5 to 10 minutes. It's really easy!
pushes the ice. I inserted the spiral piece back into the hole. I than screwed the ice dispencer
to the bin and re-inserted it back in the refrigerator.
It took me about 5 to 10 minutes. It's really easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Guy from Califon, NJ
- Parts Used:
- 215501901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Condensor fan motor failed
Removed the old fan--three small nuts and snap off connection. Ordered part and received the next day. Your company is great!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Terrell, TX
- Parts Used:
- 218832401
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
No water for ice maker and for water spout
Pull out the unit from the wall, Unplugged the frig, removed the lower cover panel. Remove 2 screws holding the water valve from the unit, then removed the 2 connectors that turn on the relays. Connected the connectors to the new valve, then replaced inside of unit and replaced the lower back panel cover, plugged it back in, then tested the water flow at the spout, and waitied for the ice maker to kick in. Worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Indianapolis, IN
- Parts Used:
- 5303918277
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker was not making ice
I replaced the solenoid first because the ice maker was not getting water. After replacing the solenoid valve, I waited about 1/2 an hour, still no water. So, I ordered a replacement ice maker. I then installed the replacement ice maker, waited a 1/2 an hour, still no water. Then, I waited overnight. Yeah, ice! WORD OF ADVICE. WAIT OVERNIGHT TO SEE IF THE ICE MAKER CREATES ICE. Not sure how long a cycle takes, but it's longer than you would think. Hope your installation is a success!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LOUIS from WOODLAND HILLS, CA
- Parts Used:
- 5303288968
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drawer tracks had cracked
it was pretty straight forward, pulled the old drawer out , emptied it out of all the food of course then i removed the front clear panel using a screw driver to gently pry off that part, the front then just slides and snaps on to the new part really easy . slide it back in and hopefully it should last another 10 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from PITTSBURGH, PA
- Parts Used:
- 5304464438
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer and refrigerator stopped cooling
The site offers a video for this part which worked perfectly. In addition to replacing the part, since the cardboard panel was off, we also cleaned all the dust off of the coils which someone recommended to do annually.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from SOUTH LYON, MI
- Parts Used:
- 241798231
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker failed
Watched YouTube video. Very easy. Used my cell phone camera in ‘selfie’ mode propped up in the upper right hand corner of freezer to see the 2 hidden screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROWENA from WIGGINS, MS
- Parts Used:
- 241685101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The drum ice maker broke in half so it couldn't dependent the ice.
I had removed the housing that the drum was in and taken the screws out to get to the broken drum. I removed it there was a set of 6 blades that crushed the ice that had to go back on the same order when I removed these I put them on a piece of wire in the order they came off (so I would get them back I the correct order). Then I reversed the order and reassembled it in the opposite direction . It was fairly easy to do. I'm a 68 year old disabled woman so if I could do it I'm sure you could to. Good luck. It cost me $14.00 if I had bought the whole assembly it would have been $150.00. So it was well worth my time and effort.
Was this instruction helpful to you?
Thank you for voting!
fridge side getting warm
Replaced both the thermostat and defrost timer and still froze up and still warm air to the fridge, turned out to be the defrost heater coil. It was cracked in the middle, very easy to test with a multimeter. Replaced the heater coil and all is like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from Middletown, DE
- Parts Used:
- 5303918277
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice maker quit making ice
I basically followed the instructions offered when i searched for the ice maker. It was relatively easy to do, I undid the 2 screws holding the ice maker to the side of the freezer, the was the tricky part, holding a mirror so i could see the slots of the screws. loosened them, disconnected the electrical connection and reversed the process for the install. It took about 25 minutes and i was back making ice.
Was this instruction helpful to you?
Thank you for voting!