FRT22RGCB4 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kelly from GILBERT, AZ
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
made lots of noise
Loosen two screws, unplug power, lift it off, put new one on and make sure water chute is correct place, tighten screws!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Lake Luzerne, NY
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
first fresh food too hot, then freezer too hot
Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done!!! Couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arand from Yorktown, IN
- Parts Used:
- 5303288973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The original support was broken, tried epoxy and it only held for a few months before breaking again
All I had to do was remove the original support that was on the inside wall of the refrigerator, which I had to use pliers since there were broken pieces, and then I just snapped the new one into the three holes provided for this support. The crisper drawer works fine now. It literally only took about 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Pinole, CA
- Parts Used:
- 215846602
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Frost in freezer, fridge not cold
From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Minneapolis, MN
- Parts Used:
- 215441502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Removeable shelf in refrigerator broke
Put the new shelf into position-Voila!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- colleen from salt lake city, UT
- Parts Used:
- 5303918277
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench (Adjustable)
ice machine was now working correctly
watched the video (VERY helpful) and then removed the old icemaker and replaced it with the new one. Difficult only because of the small working space in the side by side freezer plus you can't see what you're doing when you tighten the screws. Working like a charm now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from SPRINGFIELD, IL
- Parts Used:
- 5303918277
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker not making ice
Ordered ice maker, watch video of how to. It takes less than 5 min. Installes just like the video. Loosen 2 1/4" Screws, lift ice maker up, unplug old unit, Reverse. Just make sure water tube is lined up when you install new unit and wire is tucked up out of the way. Mine did not really start making ice till the next day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vernon from Albuquerque, NM
- Parts Used:
- 5303918277
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
I ept finding clumps of ice in try as though water was spilling over ice maker tray.
I loosened the 2 1/4 inch nuts with a nut driver, disconnected the wire harness, and removed the old unit. to replace, I simply connected the harness and bolted the unit back in. The job took about 10 to 15 minutes and the new unit works better than the old one ever did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from SOUTH CAIRO, NY
- Parts Used:
- 5303918277
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Needed to replace ice maker which had been making clicking noises as ice got jammed and then stopped working altogether.
Followed the instructions that came with replacement ice maker...was very clear and easy to follow and only took 5 minutes. I also watched the video sent via email with my order confirmation which was very well done and easy to follow. The only information that would have helped would have been a note to wait over-night for the ice maker to make ice as I thought I did something wrong when it wasn't making ice right away....waited until morning and had lots of ice. If I knew how straight forward and easy this was, I would have done it a lot sooner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TIM from WOODBURY, TN
- Parts Used:
- 218906802
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The refrigerator light would not work ...even after replacing the bulb.
I used a flat head screwdriver to pry open the front of the socket as I pushed the socket toward the freezer side. I unplugged the two wires connected to the socket then re-connected the two wires to the new socket and popped the new socket back in. I then put a new light bulb in and we had light again in the fridge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from POTTSTOWN, PA
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker stopped making ice
loosened 2 screws with 1/4 inch nut driver, disconnected electric connection lifted old ice maker out, replaced it with new one hooked up electric plug tightened 2 screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Grants, NM
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Defrost timer was not working
Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Palmdale, CA
- Parts Used:
- 215314301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Right side door was grinding on the spindal.
We took the door off and replaced the pastic washer. Found out that the repair people never informed us that the door itself has a bit damaged so this repair would have to be done over and over. Nice way for them to make money off us.
We were able to fix it so that it will last a LONG time. Sometimes it realy can pay to do-it-yourself!
We were able to fix it so that it will last a LONG time. Sometimes it realy can pay to do-it-yourself!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WAYNE from NOVATO, CA
- Parts Used:
- 5303288973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The supports for the crisper cover had broken and the draws would not open correctly
I watch the how to repair video on line and the repair went very quick and easy.It was just like the video,no hidden suprises.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- henry from alhambra, CA
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
my ice maker stopped working
removed ice maker storage holder and then remove two philip screws and unplugged four pin connector. removed ice maker and installed new one . very easy to do
Was this instruction helpful to you?
Thank you for voting!