MRS24WRAW1 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeff from GLENDORA, CA
- Parts Used:
- 5303917954
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
freezer colk, refrig warm
Followed the instructions provided in your video, took less than 15 minutes and works like new. Thank you for the parts and the advice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chester from STOCKTON, CA
- Parts Used:
- 5303288973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
4 broken drawer cover supports
Followed someone before me instructions. very simple and easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Cedar Park, TX
- Parts Used:
- 5303289501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic sidewall of drawer split
ordered new drawer, removed the clear plastic front piece from old one and installed on the new one. It was delivered only one or two days after I ordered it and was in perfect condition. Excellent service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dwayne from lincoln, NE
- Parts Used:
- 218215241
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
door closer spring had broken
A pretty easy, remove and replace, project. The spring that closes the fridge door had broken. Just pulled out the old part on top of the appliance and put in the new part. I noticed that part of the problem was that the bottem hinge needed a little lubrication too, as the door wasn't closing as easy as it should with the new part installed. I can't complain though, the side by side fridgeadaire is getting old and this was a very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chester from Oak Lawn, IL
- Parts Used:
- 215501901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fan not running.
removed old fan and replaced it.3 screws and plug.Always unplug appliance when working on it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Seal Beach, CA
- Parts Used:
- 215267701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
end piece broken that held bar on freezer door shelf
attached the bar to the end piece and slipped it into the proper opening. Easy I ordered the piece one morning and received it the next morning. Great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carol from woodland, WA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the freezer would stick in defrost and not come out
Removed the vent cover at the bottom. Removed the screws. disconected the harnes and put the new timer in. This was a very easy fix. Thank You!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colline from PENDLETON, OR
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker not making Ice
Unscrewed (loosen) screws lifted unit out unplugged electrical connection. plugged in unit hung on screws tightened screws and had ice in less then 1 hour. Rick
Was this instruction helpful to you?
Thank you for voting!
Replace the storage drawer supports and Tank Support Stud
Used pliers to remove and install tank support studs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arand from Yorktown, IN
- Parts Used:
- 5303288973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The original support was broken, tried epoxy and it only held for a few months before breaking again
All I had to do was remove the original support that was on the inside wall of the refrigerator, which I had to use pliers since there were broken pieces, and then I just snapped the new one into the three holes provided for this support. The crisper drawer works fine now. It literally only took about 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Lake Luzerne, NY
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
first fresh food too hot, then freezer too hot
Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done!!! Couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from GILBERT, AZ
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
made lots of noise
Loosen two screws, unplug power, lift it off, put new one on and make sure water chute is correct place, tighten screws!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- colleen from salt lake city, UT
- Parts Used:
- 5303918277
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench (Adjustable)
ice machine was now working correctly
watched the video (VERY helpful) and then removed the old icemaker and replaced it with the new one. Difficult only because of the small working space in the side by side freezer plus you can't see what you're doing when you tighten the screws. Working like a charm now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Pinole, CA
- Parts Used:
- 215846602
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Frost in freezer, fridge not cold
From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from State College, PA
- Parts Used:
- 5303289501, 218147701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drawer and rails broke due to under design of the components
This was the second time i replaced the drawer and the first time for the frame.The repair was simply removing the old frame from the refrig and removing the rollers from the frame with screw driver. The rollers are reused with the new frame.The frame was reinstalled in the refrig.
The replacement of the drawer requires reusing the drawer front which is easily removable. The only complication with drawer repair was the need to trim some flashing that was not removed after the molding process at the factory to allow the drawer face to fit properly on the new drawer.
this problem is a quality control issue with the manufacture of the storage drawer.
The replacement of the drawer requires reusing the drawer front which is easily removable. The only complication with drawer repair was the need to trim some flashing that was not removed after the molding process at the factory to allow the drawer face to fit properly on the new drawer.
this problem is a quality control issue with the manufacture of the storage drawer.
Was this instruction helpful to you?
Thank you for voting!