FRS26HR4AQ3 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Langley from Delberton, WV
- Parts Used:
- 241786013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced door gasket
I just pulled the old gasket out , pressed the new one in with my thumb,and was finished. thank you, Langley
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from New Orleans, LA
- Parts Used:
- 241885001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Original gate broke at the swivel point
I removed the old gate by using a flat head screw driver to pry open mouth. I then removed 2 bolts that held on the cage that hols the ice crushing blades. Then I inserted the new gate and used a screw driver to pry the mouth open again (it was more difficult to insert than remove). I then popped in the new gate and re-assembled the cage. It worked on the first shot with no problems!
This is the 3rd time I have attemped and successfully repaired major home appliances myself after the warrenty ran out. I'm sure I could buy a new appliance for the money I saved.
This is the 3rd time I have attemped and successfully repaired major home appliances myself after the warrenty ran out. I'm sure I could buy a new appliance for the money I saved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brian from mechanicsburg, PA
- Parts Used:
- 5304493021, 218904404, 240545201
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
The actuator on the water dispenser was broken and the water filter was leaking
The actuator was easy . . . just remove 6 screws (3 outside and 3 inside) and pull out assembly. The actuator popped out and I replaced it.
The water filter replacement was easy once I figured out how to use the quick connect fittings from the tube to the water filter assembly (see Youtube).
The water filter replacement was easy once I figured out how to use the quick connect fittings from the tube to the water filter assembly (see Youtube).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from traer, IA
- Parts Used:
- 5303918277
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
ice maker would not make ice
un plug fridge. removed ice maker from fridge. loosen 2 mounting screws. lift unit in slots to get over heads of screws. unplug wire harness. remove cover. remove 3 screws from control housing. remove 2 motor mounting screws. unplug motor wires from switches w/needle nose. installation is the reverse. plug in fridge turn on icemaker. takes 10 to 15 min to start to cycle.
easy and cheaper than new fridge or ice maker
easy and cheaper than new fridge or ice maker
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Kissimmee, FL
- Parts Used:
- 241786013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cracked gasket
Took off old gasket and pressed in new one. Took about 5 minutes for both procedures. Vey Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JANET from NEW FAIRFIELD, CT
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Ice Maker Doesn't Make Ice
I shut the water off under the sink and removed the back piece on the refrigerator, unscrewed the water valve, cut the ends off each plastic hose and reinserted into the new water valve. Then rescrewed the water line into the new water valve and turned on the water. Unfortunately, I was not able to get water out of the door and the ice maker still doesn't make ice. While this was an easy procedure, it didn't help me. I'm not sure I needed to replace the water valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederic from Daytona Beach, FL
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator quit running
I located the part that was the culprit as it had buzzed very much before quitting. This is an easy removal as the part is in a two prong jack and just needs to be carefully removed with the new part inserted back in the jack provided. The refrigerator works fine now, but the run capacitor will still buzz on start up of the compressor. I do hope this is normal in this model? anyway it runs fine mow. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janis from Conroe, TX
- Parts Used:
- 218904404
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Filter housing was cracked & water was leaking all over the refrigerator
First I turned off the water supply to the frig and raised the bar in the ice make to stop the production of ice. I used the nut driver to remove 3 screws from the housing. I removed the connections from the two water lines & removed the broken housing. I attached the water lines to the new housing and then screwed it back into the refrigerator. I replaced the filter and screwed the filter cup into the housing. Turned on water & ice maker, then ran water thru the door dispenser to check to see if I had done it correctly. No leaks !!! Yeah....I was done !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Brooklyn, NY
- Parts Used:
- 240351601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The bottom refrigerator door shelf bin broke.
The shelf bin is a piece that anybody can clip it on the door in less than 30 seconds. No tools required, just simple common sense.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin F. from West Falmouth, MA
- Parts Used:
- 5304491941, 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Burnt start motor relay and capacitor
Super easy. That was super cool and saved me $500.00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Leesburg, FL
- Parts Used:
- 240334201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed a new freezer door bin
One of the bins on my freezer door had the tabs, that hold it on the door, broken off. I orginally ordered the wrong item, but I called right away and Parts Select had the correct item to me immediately. It was a very easy fix, I just had to snap the bin in place once it arrived.I am very impressed with PartSelect and their service. I would definately use them again and recommend them to others.
Was this instruction helpful to you?
Thank you for voting!
door was making a popping noise when you opened the door.
First I removed the door. Took off the broken parts and replaced them. Easy and fast to repair.
Was this instruction helpful to you?
Thank you for voting!
when opening door you would hear a loud thump.
Removed stuff on door, removed 2 screws on top of door, lifted door off replaced one door closure/hinge bearing and one door closing plate and put door back on and wala no more thump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Gilbert, MN
- Parts Used:
- 5303918214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Refridgerator freezing food
Unplugged fridge from outlet. Removed rear panel on freezer side. Removed defrost thermostat from tube and cut wires. Installed new thermostat by matching color coded wires and crimping with supplied connectors and snap back on tube. Reinstalled panel and shelving.
Was this instruction helpful to you?
Thank you for voting!
The main Refidgerator door, made a cluncking sound
I removed the door by removing the top screw from the plastic cover, then slide it forward, then remove the two screws that hold the hinge on and then lifting the door off, once off the lower nylon hinge bearing comes right out of the door, the plate is removed with a screw driver. Installed in reverse order and cluncking was gone. 15 mins
Was this instruction helpful to you?
Thank you for voting!