GS21HTZBK3 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JACOB from YOUNGSTOWN, OH
- Parts Used:
- 241537103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Refrigerator did not cycle
Installation was fairly straight forward. The major complaint is that the problem returned 2 weeks later. I don’t know if I care to re-invest in another switch.
Now what?
Now what?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANIEL from CAPE CORAL, FL
- Parts Used:
- 5303918202, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
FREEZER COMPARTMENT NOT COLD ENOUGH (20 DEGREES)
REPLACED TIMER-DEFROST 215846602..REPLACED THERMOSTAT-DEFROST KIT 5303918202..REPLACED CONTROL, TEMPERATURE 5304421256..RECHARGED SYSTEM WITH 134A...ALL FANS WORKING...COMPRESSOR RUNS.. FREEZER STILL NOT GETTING COLD ENOUGH...HOLDING AT 20 DEGREES...ANY SUGGESTIONS..THANKS..DAN
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karla from UNION, MO
- Parts Used:
- 241554901
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Refrigerator light stopped working
The bulb wasn't the issue so I was hopeful the switch was. utube helped me some, but figuring my model was different than any on utube. Got the switch in and plugged it back in. Moment of truth. Didn't light. Ugggh! Out $50 for switch plus $20 for nut driver set.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kasey from O'Fallon, MO
- Parts Used:
- 240338101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
had no shelf bin
Just snapped it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Grants, NM
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Defrost timer was not working
Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W Howard from KEENE, NH
- Parts Used:
- 240396102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old part broke
The original part broke. The plastic attachment end of the part snapped off. The new part was easy to attach.
Was this instruction helpful to you?
Thank you for voting!
Meat drawer rail broken
Removed the meat drawer and shelf from refrigerator. Removed 1 screw from right side rail. Slid rail forward and removed from slot. Inserted new rail into slot, and aligned with screw hole. Installed screw. Repeated process on left side rail. Reinstalled shelf into slots and slid meat drawer into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from N LAS VEGAS, NV
- Parts Used:
- 240350609
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The glass shelf broke above the 2 drawers on the bottom
Just lay the new glass shelf into the groves. The shelf was too big and would not fit properly down into the groves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from LAGO VISTA, TX
- Parts Used:
- 240356501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic runner broken
Got the part. Watched the video. Replaced the Meat Drawer Rail. Just lke that! Easy squeezy! Thank you for making it so simple! ***** (that's five stars!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earnest from BOWDON, GA
- Parts Used:
- 241872512
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Gasket was damaged everything inside would freeze
Pulled the old gasket out and pushed the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- earl a from GIRDLER, KY
- Parts Used:
- 218906802
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light blub blew
unplug power from ref removed old light socket only difference wired a little different checked new socket compaired to old checked terminal ends small big looked at wires big,little plugged up put in new light blub plugged ref power back on work power off pushed socket bac in power on works
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from ROANOKE, VA
- Parts Used:
- 240356501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rail was broken
After removing meat tray the entire shelf including rails needs to come out. Once out a single set screw in the middle of rail needs to be removed. You can then slide the old rail across and then pull it out. Then insert new rail, slide across to lock in place. reinsert set screw. Don't over tighten. Be careful when replacing shelf as left side has air opening for drawer that must to match up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TUCSON, AZ
- Parts Used:
- 240505801
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light not turning on when door opened
Used a flat head screwdriver to pop out the old switch, removed the contacts and placed on the new switch, popped the switch back in. Done in about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brad from STOCKTON, CA
- Parts Used:
- 5303918549
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Refrigerator wasn't getting cold
removed the back panel of the freezer and unplugged the connector for the Motor. Removed the air diffuser, then removed the fan blade. Removed the 2 screws holding the motor to the bracket. Disconnected the old wire harness and installed the new one. Put the fan blade onto the new motor and installed the motor onto the bracket. Put the air diffuser back on, plugged the motor back in and fastened the back panel. Plugged the refrigerator into the outlet and tested, OK!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from Hayes, VA
- Parts Used:
- 241872512
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door gasket failed
Simple. Just pull old gasket free from door. Pace new gasket on door and ensure that gasket is seated in the gasket channel all the way around door. This part fit door properly.
Was this instruction helpful to you?
Thank you for voting!