FRT18IL6DWE Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- nathan from gillette, WY
- Parts Used:
- 5303918277
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
ice maker went bad
take the ice bin out of freezer. there are 2- 1/4" screws. these screws only need to be loosened a few turns. the ice maker can be slightly lifted up and will come off the screws. unhook the wire harness. take the "L" bracket off the old ice maker and put on the new one. set the new ice maker in. hook up the wire harness. put the new ice maker over the screws, tuck the wires out of the way and pull down into place. tighten the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from South Lyon, MI
- Parts Used:
- 240358008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer came with no shelf
The shelf fit perfectly right out of the box. It was as if it was made for it. No tools needed except for the box cutter to open the shipping carton.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bettie from Toledo, OH
- Parts Used:
- 240358008
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Had no freezer shelf.
I had to cut a little of of the ends of the shelf to make it fit. I used an angle grinder to get the job done and the shelf fits perfectly. By the way I paid for 3-5 day shipping and got it the very next day can't ask for better service than that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Micu from MOJAVE, CA
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Every thing went smooth
But I have back ground mechanical skills, I did see the video one time, and everything went smooth......
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from West Allis, WI
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
freezer defrost would melt the food
Looked up similar problems and found it to be the defrost timer. All I had to do was remove the plastic portion in the fridge section to get to the old timer. Popped the new one in and put it back together. Works great now. Would have been almost $150 to have a repair company come out and fix it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Lancaster, CA
- Parts Used:
- 240313703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The original part was plastic/and broke
unscrewed to little bolts and installed the new/metal part we got rfom partselect.If we may say.this is a great company to buy from! Fast!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from DUMAS, TX
- Parts Used:
- 240337103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
None
Real easy took out the broken ones and replaced with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from DAYTON, OH
- Parts Used:
- 240337103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Front upper edge of crisperpan was broken
Slid out old, broken pan and slid in new replacement pan.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from PUEBLO, CO
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Drive great stripped for ice eject. Heater bad
Loosened the 2 bolts 4 turns where it mounts inside the freezer. Lift maker off the bolts unplug 1 plug. Reverse to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobbie from ARLETA, CA
- Parts Used:
- 242193213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The door gasket was not working at all
I watched and followed the instructions on YouTube ?? very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curt from Maple Grove, MN
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Freezer too cold
Removed the housing with the light, 4 hexhead screws. This exposed the defrost timer, removed 2 hexhead screws, electrical connector and reassembled the unit.
Great resource and service, thank you.
Great resource and service, thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RALPH from PARIS, KY
- Parts Used:
- 240358926
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Shelf was broken
Slid the old shelf out. Attached meat drawer to new shelf and slid it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dianna from HALE, MO
- Parts Used:
- 240364787
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My Crisper cover was cracked and broken.
I ordered the replacement part. Cleaned out the bottom of my refrigerator, popped in the new part, replaced the food and was siting in my recliner in under 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from STILWELL, KS
- Parts Used:
- 242193213
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Seal damaged
Simple instructions anyone should be able to do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JUSTIN from NEW BRAUNFELS, TX
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Top cools bottom is weak
Unplug, remove 2 screws off back panel inside the freezer. Cut wires on old one and crimped in new one. Light to melt the shrink wrap that came with it. Pretty easy.
Was this instruction helpful to you?
Thank you for voting!