RT155MCV0 Frigidaire Refrigerator - Instructions

Watched the video once. Removed four 1/4 inch screws with a nut driver unplugged the unit, took out two screws securing the timer. Replaced did all of this in about 10 minutes. It was "exactly" as the video showed and it's worked perfectly since the replacement of the faulty timer. I saved a $75.00 service call minimum and the part was more than likely cheaper from Part Select than from the repair facility. Although I'm a pretty good handy man, you would not need any experience to make this repair. The instructions are precise and the part fit perfectly.

replaced broken end cap

I snapped the brackets into the ends of the shelf bar, then inserted them into the holes in the door and pulled down each end until it snapped in place.

Previously I glued them on with epoxy and Taped them. Often redoing. So I needed to clean the surface with goo gone. And to clean out the slots I used a utility knife. I had a small bump on the new end cap so I removed it with the utility knife. Simply put the end caps on the rail on each end. Then put the hooks in the slots and slide downward until it is secure. I should have thought of parts before! When the rail broke off I had cherries in a jar on that shelf. It crashed to the floor. I had a sticky mess every where.

inserted shelf caps into rack strip then into openings and hit them with my fist (gently) till they 'seated' and locked

I went on partselect put in make and model number, a list showed the probable cause. I watched the how to video. When I received the part in short order I loosened 2 screws disconnected the wiring plug (sprayed it with contact cleaner) pluged it in, removed screws from old part put them in new one. Put timer back in its location and tightened the screws. Very eazy, works fine.

I pick up very fast at these kind of small jobs but because of my very busy schedule I decided to call (2 times) technicians about my problem but none of them had any idea. About my repair, I removed the grill at the bottom of the refrigerator, unscrew a small plate (located on the bottom left side) that's holding the defrost timer. I plug on the new part, screw back the plate with the defrost timer and that was it. Don't forget to turn clockwise with your finger the timer until you hear a "click" and then turn it slightly more to the right. There is also a video on U-tube.

open freezer door two screws just below unscrew slide piece to side unplug reinstall very simple.

Unplugged the frig. Removed temp control module from frig, 1 screw with nut driver. Activated defrost timer by rotating adjustment until 2 clicks are heard. Removed two timer mounting screws, unpluged timer, plugged in the new timer, mounted it to the control module with 2 mounting screws. Replaced control module with the 1 mounting screw. Closed door and plugged it up.

Followed instruction vedeo from partselect. THANKS!!!!!

unplugged frig,removed bottom front cover and loosend 2 screws at bottom front left and slid defrost timer out from behind metal panel,unplugged the old and plugged in the new.frig works great.

I followed the procedure online and found the thermostat was ok, it had continuity when cold, and the heater coil was also ok, it too had continuity, therefore the problem was a bad defrost timer. the refrigerator works great, thanks parts select!

The repair was very easy. I had to squeeze the ends of the door shelf in a bit with pliers since the shape of the new end caps was slightly smaller than the shelf bar. BUT - here is the most important part. I had gone to a parts replacement store where I was quoted the price of $18.00 EACH for the end caps. Yes, $18.00 each!! With PartSelect, I paid less than that for the 2 caps including shipping - $15.42 total. Thank you, PartSelect.

replaced the defrosting timer and saved a lot of $ by doing it my self.

Turned off water. Took cardboard backing off lower back of unit. Unscrewed the old adaptor from the water distributor. Unscrewed the water hose connection from the adaptor. Put plumbers tape on new adaptor. Re-connected water hose to new adaptor and re-attached the adaptor to the water distributor. Turned water on, checked for leaks, and tightened adaptor to water distributor until leak stopped (approximately a quarter turn) after hand tightening. Easy, hardest part was pulling out the unit and putting it back in place!