FRS24WSGW0 Frigidaire Refrigerator - Instructions

removed water tray, used a razor blade to brake the seal from the face plate and the fridge, The hardest part was the three screws holding the dispenser face place on where rusted over. I wound up drilling them out. Once the screws removed, a slight lift, the face plate comes right off. I unplugged the cable, and set it aside. Now remove the next three screws, and the dispenser falls forward, (as far as the water line allows) undo the screws leaving the one emplace to hold the ice lever. push up twist. The hard part is getting the new one up and in. just takes a little patients.

had removed the doors to get fridge in thru small doorway when doors were reinstalled the elbow leak was replaced in about 15 minutes or less by cutting old elbow out of lines and the lines snap into new elbow with just a little force

First of all I got the part in less than 24 hours without paying any extra shipping, great service.
The part was easy to install, removed 2 screws and 2 plastic water lines, disconenected water line from the sink (turn off water first) and put in new part took less than 30 minutes and is working perfectly.

Removed four screws at top and two at bottom and pulled ice maker unit out and replaced with the new lever .

Simply detached the old ice container by removing four screws and removing one screw holding the lever onto the bottom of the container. A bit of advice; make sure you note how the spring is attached to the lever before removing the screw. It took me a bit to determine how the spring activated the lever when I was reattaching it to the bottom of the container. Also, double check your order before you finalize it. I must have inadvertently hit the item twice so I received two of them. This resulted in me having to return one item and paying for extra shipping both ways. I received the part within two days of my order. It was a very fast turn-around. Also, when I realized that I received two parts and had to call to explain the situation, I found the person on the phone to be extremely helpful and courteous. She sent me information regarding how to return the product and didn't ridicule me once for my stupidity.

Ice was not dispensing. Examined the ice bin and auger, noted that the plastic ring that holds the auger at the front of the bin was broken all the way around. Pulled out old bin, making sure the ice fill level was raised all the way up, and pushed in the new bin. The new bin filled with ice, which promptly turned into a solid mass of ice because the ice maker was also faulty. I replaced that as well and have not had any issues.

Took out old replaced with new ones, nothing to it. Better than the ease of repairing, was the sevice I received, it was the greatest, would reccommend Parts Select to my friends and family.

Removed broke bracket. Installed new bracket (part #100). Now, everything is O-TAY!

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

Looked up similar problems and found it to be the defrost timer. All I had to do was remove the plastic portion in the fridge section to get to the old timer. Popped the new one in and put it back together. Works great now. Would have been almost $150 to have a repair company come out and fix it.

But I have back ground mechanical skills, I did see the video one time, and everything went smooth......

I removed the top and bottom plastic bits that hide the screws. Then I removed the screws and put the new handle on with the same sheet-metal screws. No problems encountered.

Downloaded a schematic of the ice container. Disassembled the ice container, keeping track of which different type of screws went where. Followed the schematic to ensure proper sequence of blades and spacers. Manually rotated unit prior to installing into the freezer in case of binding. Finished.

Looked it up on how to, follow the video
. Very easy 1-2-3 it was out and new one in..........??.

take the ice bin out of freezer. there are 2- 1/4" screws. these screws only need to be loosened a few turns. the ice maker can be slightly lifted up and will come off the screws. unhook the wire harness. take the "L" bracket off the old ice maker and put on the new one. set the new ice maker in. hook up the wire harness. put the new ice maker over the screws, tuck the wires out of the way and pull down into place. tighten the screws.