FRS20HRAD0 Frigidaire Refrigerator - Instructions

I went on partselect put in make and model number, a list showed the probable cause. I watched the how to video. When I received the part in short order I loosened 2 screws disconnected the wiring plug (sprayed it with contact cleaner) pluged it in, removed screws from old part put them in new one. Put timer back in its location and tightened the screws. Very eazy, works fine.

I pick up very fast at these kind of small jobs but because of my very busy schedule I decided to call (2 times) technicians about my problem but none of them had any idea. About my repair, I removed the grill at the bottom of the refrigerator, unscrew a small plate (located on the bottom left side) that's holding the defrost timer. I plug on the new part, screw back the plate with the defrost timer and that was it. Don't forget to turn clockwise with your finger the timer until you hear a "click" and then turn it slightly more to the right. There is also a video on U-tube.

Removed front panel out of existing drawer, it slid up and out, slid it into new drawer, drawer was as good as new!

open freezer door two screws just below unscrew slide piece to side unplug reinstall very simple.

snapped the wires from frig onto the proper prong and viola,it works. The proper prong is identified by the size because there are two prongs with the wires and two connecting prongs in the socket. I talked to a very helpful representative and she gave me the number for Frigidaire, when I was confused by the placement of the wire. Wish I had remembered her name to share with you. As it turned out I didn't need to call Frigidaire.

Ordered the new part-Unplugged the refrigerator - took off the cover over the defective timer - put in the new part put the cover back on - plugged the refrigerator back in - so far, so good!~

Removed the lower trim panel from front of fridg. and loosened two screws enough to turn it about 1/4 inch so the screw heads were in the larger holes. Pulled it out disconnected the wire connector and transfered the heat shield and screws to the new clock, connected the wire connector and aligned the screws. tightened them and job done. Has worked like new sense. Thanks Roger

I used a pick to remove the lugs from the old starter. Clicked them right in the new one and it went to woking!!!

Unplugged the frig. Removed temp control module from frig, 1 screw with nut driver. Activated defrost timer by rotating adjustment until 2 clicks are heard. Removed two timer mounting screws, unpluged timer, plugged in the new timer, mounted it to the control module with 2 mounting screws. Replaced control module with the 1 mounting screw. Closed door and plugged it up.

I first thought the defroster heater broke - took the back wall of the freezer off and cooling fins were fine. Then took the defroster timer out and opened it up. The contacts were badly burnt so the compressor and fan ran during only part of the cooling cycle. Replacing the timer took less than 5 minutes - turn off the power, remove one screw to take out the control box, cut the ground wire (new timer housing is plastic and does not have a ground connection), remove two screws to unmount the timer, unplug the old timer, plug in the new timer, fasten with two screws, put the control unit in and fasten with one screw, turn power back on.

real easy with the help of the video , made the difference

You guys at Partselect are the best!!! Went to your site, typed in my appliance symptoms, and received possible fixes. Ordered the suggested parts (under $50) on a Sunday night and got em Tuesday am. Installed the easiest one first and Voila!!!! Frig is working great. Thanks Bob S

Remove 4 screws that hold up overhead controls, this is also the part that holds the light. Unplug the timer and replace. Super simple and runs great now. After you plug it in it may take a few minutes to kick on the compressor but it will. Also I was pleased it was a factory Frigidare part. Price was right.

Purchased switch and socket, not sure which had failed. Moved all frozen food to refrigerator, turned off breaker. Used nutdriver to remove two screws holding box containing switch and socket. Removed old switch and socket. Removal was slightly difficult since cabling came off both sides of the box. Installed new switch and socket and bulb. Turned breaker back on, checked light as workiing. Replaced scrrews to re-intstall switch box ( or whatever you call it ) Closed door and waited for freezer to cool. Returned all frozen food to freezer. Job Done

bottom left cornerof fridge defrost timer replaced two bolts and a wire