FRS23KF5DW4 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Louisville, KY
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
water valve failure
removed rear cover, removed screws, diconnected water line connections, cut off old water line connection, installed new compression water line connection, replace screws in water line housing, replace rear cover.
worked fine
worked fine
Was this instruction helpful to you?
Thank you for voting!
The meat keeper drawer kept falling
Backed one screw off each side of the shelf brackets, snapped old ones out, snapped new ones in and replaced the screw. Spend more time taking food off the shelf than it did to make the repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Dover, NH
- Parts Used:
- 240324501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wrong part
Call before ordering and confirm it is the right part.
Was this instruction helpful to you?
Thank you for voting!
Rust had corroded Front Plate and Drive Blade
Installation was completed by following the online Parts diagram. Had to completely remove all parts, including the blades in ice crusher, and re-assemble. Glad the online diagram was clear and easy to read.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Middletown, CT
- Parts Used:
- 5304469407
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Motor had failed due to ice ejector frozen to tray.
Removed the ice maker. Took off the cover and proceed to remove the motor. The only trick was to dis-assemble the electrical connector to replace the wires. I chose to do this rather than splice the new motor into the existing system and it was simple with a little patience.
Easiest repair to make and half / third the money for a new ice maker. The in-laws have ice again (it was over a year).
Easiest repair to make and half / third the money for a new ice maker. The in-laws have ice again (it was over a year).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DeFuniak Spgs, FL
- Parts Used:
- 5303918344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
ice maker motor shorted out
loosen 2 screws
unplug connector
remove
replug
replace
tighten 2 screws
done
unplug connector
remove
replug
replace
tighten 2 screws
done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tina from Baroda, MI
- Parts Used:
- 240356501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My son pulled on the meat pan & cracked the right support.
The old support just unscrewed & then the new one screwed right on with two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Wyomissing, PA
- Parts Used:
- 240359001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The freezer door bin broke while overstuffing it.
Well...The freezer door bin broke while over-stuffing it with frozen deer jerky. I called my local repair shop and they quoted me what was above retail for the piece...I checked online liked the prices and felt confident to buy from parts select. I bought on a Saturday and selected the slowest shipping (I think 5 days). I got a 'notice' it shipped on Monday and had it Tuesday when I got home from work. Excellent experience.
Was this instruction helpful to you?
Thank you for voting!
crisper drawer supports broke
The parts supplied were made to fit. The hardest part was getting the original broken tabs out of the internal walls of the fridge with out damaging the internal insulation. I punched the center locking pin through completely, dug out the broken tabs and then reached into the hole with a dental pick and pulled out the center pin. The new parts fit perfectly and with a plastic mallet, tapped the new locking pin into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from PITTSBURGH, PA
- Parts Used:
- 5304464438
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer and refrigerator stopped cooling
The site offers a video for this part which worked perfectly. In addition to replacing the part, since the cardboard panel was off, we also cleaned all the dust off of the coils which someone recommended to do annually.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paulo from Round Lake, IL
- Parts Used:
- WF2CB
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice/water filter needs replacement after 7 months
I just took the old filter off and replaced with the new one, after I run the water for about 15 minutes and tossed the old ice and cleaned the tray.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myron from Tumwater, WA
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Ice maker malfunctioned
We followed the video instructions and it went fairly smooth. After turning off the water at the street we found that the faucet at the wall had it's own "on/off" valve. When finished, we turned on the power and heard the gears going through their revolutions, but no ice was made. We waited 24 hours and still no ice. I removed the cover on the ice maker and adjusted the amount of water to see if that was malfunctioning. Still no ice was created. Waited another 24 hours - nothing. Waited another 24 hours (the site said that sometimes the ice maker would take time to reset itself) - nothing. Then on the fourth day after changing out the triple water valve we heard water being dispensed and later that day it put out the first ice in weeks. Another hour later another batch of ice cubes were ready and deposited into the bin. Since that time, we have had a full bin. I moved the set screw back to it's original setting because a little too much water was being delivered. The cubes weren't separating to individual cubes. That cleared up the problem. This was easily completed - we recommend others do their own work. Just be patient for the system to reset itself.
Was this instruction helpful to you?
Thank you for voting!
Ice Would Not Dispence
Took the ice storage bin out. Took the unit apart,and disamble the augar unit. Ordered parts from manufacture, which arrived in two days. As soon as I got the parts, I reassambled it. Work perfect. Good job!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIKE from MELBOURNE, KY
- Parts Used:
- WF2CB
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water filter
pushed release button removed filter, installed new filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Curwensville, PA
- Parts Used:
- 241682001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Water actuator broke off on door.
Fridge has Ice & water in Door.
Slide bottom plate out.Remove three screws
across bottom.
Remove two screws that holds a circut board.
pull the water hose off and remove board.The hose is a little tricky getting back on.
remove two screws that holds two little plates and remove old part.
Reverse prosedure to put back.
Slide bottom plate out.Remove three screws
across bottom.
Remove two screws that holds a circut board.
pull the water hose off and remove board.The hose is a little tricky getting back on.
remove two screws that holds two little plates and remove old part.
Reverse prosedure to put back.
Was this instruction helpful to you?
Thank you for voting!