FRT21NSGD0 Frigidaire Refrigerator - Instructions

Followed instruction vedeo from partselect. THANKS!!!!!

unplugged frig,removed bottom front cover and loosend 2 screws at bottom front left and slid defrost timer out from behind metal panel,unplugged the old and plugged in the new.frig works great.

pulled down the thermostat cover and unpluged the timer control and replaced it with the new part. total time to repair was about 15 min. there was a vidio on how to replace the new part that just informed me that I did it right!!!!very easy site to find what you are looking for!!!!

replaced the defrosting timer and saved a lot of $ by doing it my self.

Just followed the online instruction video .It was very easy.

You guys at Partselect are the best!!! Went to your site, typed in my appliance symptoms, and received possible fixes. Ordered the suggested parts (under $50) on a Sunday night and got em Tuesday am. Installed the easiest one first and Voila!!!! Frig is working great. Thanks Bob S

Remove 4 screws that hold up overhead controls, this is also the part that holds the light. Unplug the timer and replace. Super simple and runs great now. After you plug it in it may take a few minutes to kick on the compressor but it will. Also I was pleased it was a factory Frigidare part. Price was right.

Based on the diagnosis on this site I thought the 66% odds of the problem being the Defrost Timer looked pretty good, $30 including shipping versus a Sears tech phone estimate of $250-300. BINGO! Just follow the online installation instructions and don't forget to use the reset switch as described. Works like new! THANK YOU

The rail holding up the deli drawer has clips (not screws) which attach to the upper shelf. My husband accused my of overloading the bin because the drawer kept falling down. He thought by tightening the screws, the problem was solved..No! Instead, when he went home for a few days (this is a vacation home) the rail cracked. I went on line AND called to make sure the replacement part was correct. I spoke to the nicest most helpful and patient man, ordered the part, received it in three days,screwed the old clips into the new rail and attached the rail to the shelf in 5 minutes. I would have paid double the price (it was so reasonable) just not to hear him moan, carry-on, complain about the HARD WORK and time he has to waste on repairs. I had to show him the packaging and broken rail (with a larger , incorrect sized screw he used!) because he could not believe that I (andsolved this problem...Thank you! you)

I followed the procedure online and found the thermostat was ok, it had continuity when cold, and the heater coil was also ok, it too had continuity, therefore the problem was a bad defrost timer. the refrigerator works great, thanks parts select!

Decided to clean the refrigerator at the same time as replacing the broken part. Took shelf out, removed glass, washed all parts, removed broken rail (two screws) and replaced new part. Piece of cake!

I first thought the defroster heater broke - took the back wall of the freezer off and cooling fins were fine. Then took the defroster timer out and opened it up. The contacts were badly burnt so the compressor and fan ran during only part of the cooling cycle. Replacing the timer took less than 5 minutes - turn off the power, remove one screw to take out the control box, cut the ground wire (new timer housing is plastic and does not have a ground connection), remove two screws to unmount the timer, unplug the old timer, plug in the new timer, fasten with two screws, put the control unit in and fasten with one screw, turn power back on.

real easy with the help of the video , made the difference

Having looked at the broken area, in some frustration, for several years, I had a good idea how it all went together: the front end slips over a metal lip suspended from the front of the shelf above, and the rear is held in place by a single screw (single slot with hex-dead). The most time was taken clearing the items off the shelf above. Having done that, the shelf was easily lifted up and removed. Flip it over to expose the screw at the back. Remove that screw and discard the old/broken hanging rail. Slip the front end of the new rail (carefully) over the metal lip. At the rear, line up the hole on the hanger with the hole in the mounting bracket and re-insert the one screw. Re-install shelf and slide the drawer back into place on the hangers. Good to go.

I went on partselect put in make and model number, a list showed the probable cause. I watched the how to video. When I received the part in short order I loosened 2 screws disconnected the wiring plug (sprayed it with contact cleaner) pluged it in, removed screws from old part put them in new one. Put timer back in its location and tightened the screws. Very eazy, works fine.