GLRT185TDQ8 Frigidaire Refrigerator - Instructions

Took off the old one, replace the new one in less than 5 minutes

The parts were easily replaceable. No special instructions needed. Just identify and remove and replace. I didn't know which specific part needed to be replaced (both reported to fix my problem) but neither part was very expensive so I replaced both. No special tools needed. 1/4" nutdriver and phillips head screwdriver. Repair took about 30 minutes. I did have to make an adjustment on the defrost timer (a small dial on the unit) I just set it how the old part was set. I immediately knew it was going to work when I plugged the refrigerator back in and the fan motor inside the freezer kicked on. Easy peesy...

I followed your video instructions, is very important to have this information.

Before buying the part, I watched your video and realized it was extremely simple to remove and replace. Item was to take 7-10 days and I received it in 4. Took longer than 15 minutes because I had to move the fridge forward, get my tools and a vacuum, get a cup of coffee and get to it. Very easy and the video was exactly step by step. It took longer to vacuum all of the dust bunnies than to replace the part.

Honestly, I was in the market to buy a new refrigerator but now I believe I'll wait several more years. Thank you for your support.

I initially replaced the defrost timer, and later replaced it and the defrost thermostat. The defrost thermostat was the faulty component

inside the freezer compartment, remove four hex head screws from rear panel,lift panel forward and unplug wire assembly from panel. find old defrost thermostat attached to copper tube by clip on back of thermostat, unclip, snip two wires to thermostat, take new thermostat, strip 1/4"of wire from wires in freezer (thermostat is prestripped),insert light blue wire from thermostat and light blue wire from freezer into opposite ends of crimp connector and crimp securely. repeat with dark blue wires. set panel back in freezer,connect plug to back of panel, refasten screws and you are go to go! save yourself the price of a new refrigerator or $300 repair by repairman!

Just like the video , just pull out the crisper drawers and slide the new one in. I also made sue that I had a quilt on the floor in case I dropped the glass shelf. Also if you are not sure of the model number you can try calling the store where you bought the appliance at which I had to do. I bought it at Conns and they just needed the phone number I used when I bought it.

I followed the instructions on your website, made it a simple as possible. Very tight work area sometimes fingers only, but a little patience works.
Saved at least $300. By not paying a repair person.

replaced broken one

Pulled off the old seal and put the new one on. No tools needed. It fit where it was supposed to and seals the door like new now! Thank you!

Literally all I needed to do for the door shelf was press it into place, and for the crisper drawer cover so just needed to remove the crisper drawers, lift away the glass shelf (after removing contents from the fridge, obviously) and then remove the drawer frame and replace the broken one (which again, had been broken from before I moved in here almost six years ago!), and then reassemble. It's very nice to have space for seltzer or beer cans in the door and not to have the sagging shelf like I had before. Worth the money and very easy to source.

Took the drawer and shelf out then took the screw out and took the old one out and then put the new one on.

Followed the installation instruction for both parts now both the freezer and refrigerator are getting cold

Removed the vent cover at the bottom. Removed the screws. disconected the harnes and put the new timer in. This was a very easy fix. Thank You!

From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.